5A06铝合金TIG丝材-电弧增材制造工艺
TIG Wire and Arc Additive Manufacturing of 5A06 Aluminum Alloy

黄丹 ¹ 朱志华 ² 耿海滨 ³ 熊江涛 ³ 李京龙 ³ ^* 张赋升 ³

文摘	选用Φ1. 2mm的5A06铝焊丝为成形材料,研究TIG丝材-电弧增材制造工艺。以TIG焊机为电源(交流模式),以四轴联动数控机床为运动机构,研究单层和多层成形时预热温度和电流对成形形貌的影响,观察成形件微观组织,并测试其力学性能。建立了单层单道基板预热温度和电弧峰值电流工艺规范带判据,以保证良好成形。结果表明:成形件的高度从第一层的3.4 mm急剧下降,直到第8层后高度稳定在1.7mm。层间组织为细小的树枝晶和等轴晶;层间结合处组织最粗大,为柱状树枝晶;顶部组织最细小,由细小的树枝晶转变为等轴晶。成形件的力学性能各向同性,抗拉强度为295MPa,伸长率为36%。
其他语种文摘	Wire and arc additive manufacturing(WAAM) was investigated by tungsten inert gas arc welding method(TIG),in which φ1. 2mm filler wire of aluminum alloy 5A06( Al-6Mg-Mn-Si) was selected as deposition metal. The prototyping process was conducted by a TIG power source (working in AC mode) manipulated by a four-axis linkage CNC machine. Backplate preheating temperature and arc current on deposited morphologies of single layer and multi-layer were researched. The microstructure was observed and the sample tensile strength was tested. For single layer, a criterion that describes the correlation between backplate preheating temperature and arc peak current, of which both contribute to the smoothening of the deposited layer. The results show that the layer height drops sharply from the first layer of 3. 4mm and keeps at l. 7mm after the 8th layer. Fine dendrite grain and equiaxed grain are found inside a layer and coarsest columnar dendrite structure at layer boundary zone; whereas the microstructure of top region of the deposited sample changes from fine dendrite grain to equiaxed grain that turns to be the finest structure. Mechanical property of the deposited sample is isotropic, in which the tensile strength is approximately 295MPa with the elongation around 36%.
来源	材料工程 ,2017,45(3):66-72 【核心库】
DOI	10.11868/j.issn.1001-4381.2015.000552
关键词	TIG ; 丝材-电弧增材制造 ; 5A06铝合金 ; 成形 ; 微观组织 ; 力学性能
地址	1. 西北工业大学, 凝固技术国家重点实验室;;摩擦焊接陕西省重点实验室, 西安, 710072 2. 北京航天动力研究所, 北京, 100076 3. 西北工业大学, 摩擦焊接陕西省重点实验室, 西安, 710072
语种	中文
文献类型	研究性论文
ISSN	1001-4381
学科	金属学与金属工艺
基金	西北工业大学凝固技术国家重点实验室开放基金 ; 国家自然科学基金资助项目
文献收藏号	CSCD:5949318