高温短时间时效处理对Mg-3Nd-lZn合金微观组织及力学性能的影响
EFFECTS OF HIGH TEMPERATURE SHORT TIME AGEING TREATMENT ON THE MICROSTRUCTURES AND MECHANICAL PROPERTIES OF Mg-3Nd-lZn ALLOY
查看参考文献25篇
|
文摘
|
将固溶处理后的Mg-2.7Nd-0.6Zn-0.5Zr合金在200~300 ℃之间进行不同温度及时间的高温时效处理,研究高温短时间时效处理对合金的微观组织和力学性能的影响,并利用OM,SEM和TEM对合金的微观组织进行表征.结果表明,固溶态Mg-2.7Nd-0.6Zn-0.5Zr合金经250~275 °C高温短时间时效后,其室温屈服强度和抗拉强度最高分别增加了近70%和29%,宏观组织中出现呈直线性不均匀分布的析出相.析出相的显微形貌为颗粒状,成分为Mg_(12)Nd.析出相的线性分布方向平行于Mg基体(0001)_(Mg)基面,合金的时效硬化行为与这种沿基面呈平行线分布的颗粒状析出相密切相关.在250~275 °C范围内时效20~30 min后屈服强度较高,这是由于在变形过程中颗粒状Mg12Nd的特殊分布对基面滑移及晶粒间协调变形起到很强的抑制作用. |
|
其他语种文摘
|
Among the traditional cast magnesium alloys system, Mg-3Nd- lZn alloy with high strength and heat resistance, has been widely applied in aeronautics such as in engine box and wing rib of airplane. In present research, the as-cast Mg-2.7Nd-0.6Zn-0.5Zr (NZ31) alloy was solution treated and then aged at temperatures ranging from 200 °C to 300 °C. The microstructures and mechanical properties of the aged specimens especially at relatively high temperature (225-300 °C) were systematically characterized by OM, SEM and TEM. A new kind of precipitates distributed in line was clearly found in the specimens aged at high temperature (225~275 °C) for a short time (15-30 min), which corresponded to a significant enhancement of hardness and tensile strength at room temperature. The TEM results showed that the precipitates distributed in line had a composition of Mgi2Nd and a granular shape, and mainly formed along the (0001)_(Mg) basal plane. The special distribution of the granular Mg_(12)Nd precipitates was effective barriers to the basal slips and may probably restrain the intergranular coordination during tensile deformation, leading to a large strengthening effect, that is, the yield strength and ultimate tensile strength, of the NZ31 alloy aged at 250~275 °C for 20?30 min, increased by about 70% and 29% respectively, in comparison with only the solutionized one. |
|
来源
|
金属学报
,2016,52(5):567-574 【核心库】
|
|
DOI
|
10.11900/0412.1961.2015.00333
|
|
关键词
|
镁合金
;
时效
;
析出相
;
力学性能
|
|
地址
|
1.
中国科学院金属研究所, 沈阳, 110016
2.
沈阳理工大学材料科学与工程学院, 沈阳, 110159
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
0412-1961 |
|
学科
|
一般工业技术 |
|
基金
|
国家自然科学基金
;
国家973计划
|
|
文献收藏号
|
CSCD:5688934
|
参考文献 共
25
共2页
|
|
1.
Nie J F.
Acta Mater,2000,48:1691
|
CSCD被引
123
次
|
|
|
|
|
2.
王小娜. NZ30K镁合金时效析出动力学与强化模型的研究.
金属学报,2014,50:355
|
CSCD被引
5
次
|
|
|
|
|
3.
刘庆. 镁合金塑性变形机理研究进展.
金属学报,2010,46:1458
|
CSCD被引
121
次
|
|
|
|
|
4.
唐伟. 热处理对AZ80镁合金结构及性能的影响.
金属学报,2005,41:1199
|
CSCD被引
40
次
|
|
|
|
|
5.
Li D J.
Mater Sci Eng, A,2009,526:150
|
CSCD被引
7
次
|
|
|
|
|
6.
Liu X B.
Mater Sci Eng, A,2008,497:326
|
CSCD被引
11
次
|
|
|
|
|
7.
Li J H.
Mater Sci Eng, A,2012,534:1
|
CSCD被引
3
次
|
|
|
|
|
8.
Liu H.
Acta Mater,2014,77:133
|
CSCD被引
11
次
|
|
|
|
|
9.
Fu P H.
Mater Sci Eng, A,2008,496:177
|
CSCD被引
20
次
|
|
|
|
|
10.
Dai J.
Mater Sci Eng, A,2011,529:401
|
CSCD被引
2
次
|
|
|
|
|
11.
Ma L.
Mater Sci Eng, A,2012,543:12
|
CSCD被引
11
次
|
|
|
|
|
12.
Wu D.
Mater Des,2014,58:324
|
CSCD被引
10
次
|
|
|
|
|
13.
Zheng X W.
Mater Sci Technol,2011,21:275
|
CSCD被引
1
次
|
|
|
|
|
14.
Ning Z L.
J Mater Sci,2009,44:4264
|
CSCD被引
6
次
|
|
|
|
|
15.
Wang K F.
Hot Working Technol,2011,40:39
|
CSCD被引
1
次
|
|
|
|
|
16.
Wang W H.
Mater Sci Eng, A,2016,649:214
|
CSCD被引
12
次
|
|
|
|
|
17.
Nie J F.
Metall Mater Trans, A,2012,43:3891
|
CSCD被引
210
次
|
|
|
|
|
18.
Pike T J.
J Less Common Met,1973,30:63
|
CSCD被引
13
次
|
|
|
|
|
19.
Fu P H.
Mater Sci Eng, A,2008,486:183
|
CSCD被引
45
次
|
|
|
|
|
20.
Wang W H.
Mater Sci Forum,2015,816:362
|
CSCD被引
2
次
|
|
|
|
|
了解气象卫星更多信息，请访问