热处理对7A85铝合金组织和性能的影响
Effects of Heat Treatment on Microstructure and Properties of 7A85Aluminium Alloy
查看参考文献18篇
文摘
|
采用室温拉伸测试,电导率测试,晶间腐蚀及透射电镜等手段研究不同时效制度对7A85铝合金显微组织,力学性能以及晶间腐蚀性能的影响。结果表明:合金经过峰时效(120℃/24h)处理,抗拉强度,伸长率和电导率分别达到760.8MPa,8.9%和29.7%IACS;合金的主要强化相为GP区,峰时效(T6)合金晶内分布着大量细小而弥散的GP区和少量的η′相。双级时效(120℃/8h+165℃/12h)时,合金抗拉强度及电导率分别达到597.7MPa和38.1%IACS,且随着时效时间的延长,晶间析出相长大粗化,PFZ带宽化,晶间腐蚀敏感性降低。因此,采用120℃/8h+165/12h双级时效可以获得较好的综合性能。 |
其他语种文摘
|
The influence of heat treatment on microstructure,mechanical properties and intergranular corrosion(IGC)of 7A85 aluminum alloy was investigated by tensile testing,conductivity testing,intergranular corrosion testing and transmission electron microscope.The results show that tensile strength,elongation and conductivity of 7A85 aluminium alloy aged at 120℃ /24hare 760.8MPa, 8.9% and 29.7% IACS respectively;the main strengthening precipitates in the alloy are GP zones. While the tensile strength and the conductivity of 7A85aluminium alloy reach 597.7MPa and 38.1% IACS respectively,after duplex aging at 120℃ /8h+165℃ /12h,and with increase of aging time,the precipitates in the matrix become coarser and PFZs become broaden,resulting in the susceptibility to IGC decreasing.Therefore,the alloy after duplex aging at 120℃ /8h+165℃ /12hshows good comprehensive performance. |
来源
|
材料工程
,2015,43(8):13-18 【核心库】
|
DOI
|
10.11868/j.issn.1001-4381.2015.08.003
|
关键词
|
7A85铝合金
;
时效硬化
;
显微组织
;
晶间腐蚀
|
地址
|
1.
湖南大学材料科学与工程学院, 长沙, 410082
2.
北京航空材料研究院, 北京, 100095
|
语种
|
中文 |
文献类型
|
研究性论文 |
ISSN
|
1001-4381 |
学科
|
金属学与金属工艺 |
基金
|
国家自然科学基金资助项目
;
广东省教育部产学研结合专项资金资助项目
|
文献收藏号
|
CSCD:5491250
|
参考文献 共
18
共1页
|
1.
Heinz A. Recent development in aluminum alloys for aerospace applications.
Materials Science and Engineering:A,2000,280(1):102-107
|
被引
357
次
|
|
|
|
2.
胡本润. 7050铝合金锻件缺陷容限值试验方法研究.
航空材料学报,2015,35(1):82-86
|
被引
3
次
|
|
|
|
3.
王少华. Al-Zn-Mg-Cu-Zr-0.5Er合金型材组织性能研究.
材料工程,2014(3):27-33
|
被引
2
次
|
|
|
|
4.
宁爱林.
析出相及其分布对高强铝合金力学性能的影响,2007
|
被引
5
次
|
|
|
|
5.
辛星. 回归再时效中预时效温度对7050铝合金应力腐蚀性能的影响.
材料工程,2014(5):29-34
|
被引
6
次
|
|
|
|
6.
Adler P N. Calorimetric studies of 7000series aluminum alloys:Ⅱ.comparison of 7075,7050and RX720alloys.
Metallurgical Transactions A,1977,8(7):1182-1190
|
被引
17
次
|
|
|
|
7.
Robson J D. Microstructural evolution in aluminum alloy 7050 during processing.
Materials Science and Engineering:A,2004,382:112-121
|
被引
84
次
|
|
|
|
8.
Sha G. Early-stage precipitation in Al-Zn-Mg-Cu alloy(7075).
Acta Materialia,2004,52(15):4503-4516
|
被引
180
次
|
|
|
|
9.
Saleh A E A. Intergranular corrosion behavior of the 7075-T6 aluminum alloy under different annealing conditions.
Materials Chenistry and Physics,2011,126(3):607-613
|
被引
1
次
|
|
|
|
10.
Chen Songyi. Effect of heat treatment on strength,exfoliation corrosion and electrochemical behavior of 7085aluminum alloy.
Materials and Design,2012,35:93-98
|
被引
32
次
|
|
|
|
11.
Sprowls D O. Fundamental aspects of stress corrosion cracking.
National Association of Corrosion Engineers,1969:466-512
|
被引
1
次
|
|
|
|
12.
万彩云.
AlZnMgCu合金微观组织及强化相的研究,2010
|
被引
1
次
|
|
|
|
13.
Valiev R Z. A nanostructural design to produce high-strength Al alloys with enhanced electrical conductivity.
Scripta Materialia,2014,76:13-16
|
被引
21
次
|
|
|
|
14.
田莳.
金属物理性能,1994:36-37
|
被引
6
次
|
|
|
|
15.
Han N M. Effects of prestretching and ageing on the strength and fracture toughness of aluminum alloy 7050.
Materials Science and Engineering:A,2011,528(10):3714-3721
|
被引
36
次
|
|
|
|
16.
贺俊光. 第二相对Al-Zn-Sn-Ga-Mg合金腐蚀行为的影响.
中国有色金属学报,2013,23(3):628-634
|
被引
6
次
|
|
|
|
17.
Davies J R.
Corrosion of aluminum and aluminum alloys,1999:28-29
|
被引
4
次
|
|
|
|
18.
李国峰. 回归冷却速率对7050铝合金力学性能及晶间腐蚀抗力的影响.
中国有色金属学报,2013,23(5):1234-1240
|
被引
1
次
|
|
|
|
|