牙轮钻工作参数与岩体强度对应关系的理论分析与实验研究
Theoretical and experimental studies on relationship between working parameters of cone drill and rock strengths
查看参考文献13篇
|
文摘
|
以露天矿开采为背景,基于牙轮钻单齿冲击压入破岩的机理,借助理论分析及现场实验,建立了牙轮钻的工作参数(进尺速度、钻杆轴压、转速)与岩体强度(黏聚力、内摩擦角)的对应关系。理论分析时,基于布西内斯科问题弹性力学解和Drucker-Prager 塑性准则,给出了单齿压入破碎区域的几何形态,建立了单齿破岩体积与钻杆轴压、黏聚力、内摩擦角间的函数关系;并根据钻杆旋转一周单齿破岩体积的累积量和宏观破岩体积相等,建立了进尺速度、转速与单齿破岩体积的对应关系。理论分析的结果表明,单齿作用下,破碎区域基本呈椭球形,并在压入点附近的表层出现薄层破碎;进尺速度与转速呈线性关系,进尺速度与钻杆轴压呈3/2次方的关系,进尺速度与黏聚力呈-3/2次方的关系,内摩擦角对进尺速度的影响可以忽略。在鞍千矿南采区进行了牙轮钻钻进规律的现场实验,研究了进尺速度与钻杆轴压、转速、黏聚力间的对应关系,得到了与理论分析一致的结果。研究成果可以为牙轮钻工作参数的优化设计及岩体强度的动态测试提供依据。 |
|
其他语种文摘
|
The relationship between operating parameters of cone drill (drilling speed, drill pipe axial force, rotational speed) and rock mass strengths (cohesion, internal friction angle) is established by means of theoretical analysis and field tests based on the single-tooth impact and pressure rock fragmentation mechanisms. The geometrical morphology of broken area by single-tooth is obtained, and the relationship among single-tooth rock fragmentation volume, drill pipe axial force, cohesion and internal friction angle is established based on the Boussinesq elasticity solution and D-P plastic criterion in theoretical analysis. The relationship among single-tooth rock fragmentation volume, drilling speed and rotational speed established by the relationship that the accumulation of single-tooth rock-breaking volume and the macro rock volume is equal when the drill pipe rotates a circle. The results of theoretical analysis show that the fractured area basically exbibits ellipsoid and a thin layer in the surface layer under the single-tooth pressure. The relationship between drilling speed and rotational speed is linear, that between drilling speed and drill pipe axial force is 3/2 power, and that between drilling speed and cohesion is-3/2 power. The influence of internal friction angle on the penetration rate can be ignored. Field tests on the drilling law of conedrill are conducted in the south mining area of Anqian Mine, and the relationship among drilling speed, drill pipe axial force, rotational speed and cohesion is obtained. The theoretical analysis and the actual measurements coincide fairly well. The research achievements may provide a basis for the optimization design of working parameter of conedrill and dynamic tests on rock mass strengths. |
|
来源
|
岩土工程学报
,2016,38(7):1221-1229 【核心库】
|
|
DOI
|
10.11779/cjge201607008
|
|
关键词
|
牙轮钻
;
单齿破岩体积
;
轴压
;
进尺速度
;
岩体强度
;
D-P 塑性准则
|
|
地址
|
1.
中国科学院力学研究所, 中国科学院流固耦合系统力学重点实验室, 北京, 100190
2.
广东宏大爆破股份有限公司, 广东, 广州, 510623
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1000-4548 |
|
学科
|
建筑科学 |
|
基金
|
国家973计划
;
中国科学院战略性先导科技专项
;
国家自然科学基金青年科学基金
;
广东宏大爆破股份有限公司项目资助
|
|
文献收藏号
|
CSCD:5752987
|
参考文献 共
13
共1页
|
|
1.
王清峰. 牙轮钻头单牙轮的破岩仿真研究.
振动与冲击,2010,29(10):108-112
|
CSCD被引
16
次
|
|
|
|
|
2.
杨岳峰. 冲击作用下的压头破岩机制研究.
岩土力学,2013,34(6):1775-1786
|
CSCD被引
8
次
|
|
|
|
|
3.
Lawn B R. Microfracture beneath point indentations in brittle solids.
Journal of Materials Science,1975,10(1):113-122
|
CSCD被引
29
次
|
|
|
|
|
4.
Lindqvist P A. Stress fields and subsurface crack propagation of single and multiple rock indentation and disc cutting.
Rock Mechanics & Rock Engineering,1984,17(2):97-112
|
CSCD被引
6
次
|
|
|
|
|
5.
Hertz H. On the contact of elastic solids.
Journal Fur Die Reine Und Angewandte Mathematik,1988,92:156-228
|
CSCD被引
3
次
|
|
|
|
|
6.
Ostojic P. A review of indentation fracture theory: its development, principles and limitations.
International Journal of Fracture,1987,33(4):297-312
|
CSCD被引
6
次
|
|
|
|
|
7.
赵伏军. 动静载荷耦合作用下岩石破碎理论分析及试验研究.
岩石力学与工程学报,2005,24(8):1315-1320
|
CSCD被引
20
次
|
|
|
|
|
8.
刘清友. 盘式单牙轮钻头破岩机理仿真研究.
四川大学学报(工程科学版),2003,35(5):12-15
|
CSCD被引
7
次
|
|
|
|
|
9.
Liu H Y. Numerical simulation of the rock fragmentation process induced by indenters.
International Journal of Rock Mechanics & Mining Sciences,2002,39(4):491-505
|
CSCD被引
38
次
|
|
|
|
|
10.
石祥超. 加载速度对单齿压入破岩过程的影响.
石油钻探技术,2010,38(4):19-21
|
CSCD被引
3
次
|
|
|
|
|
11.
Su O. Numerical simulation of rock cutting using the discrete element method.
International Journal of Rock Mechanics & Mining Sciences,2011,48(3):434-442
|
CSCD被引
39
次
|
|
|
|
|
12.
祝效华. 牙轮钻头动力学特性仿真研究.
石油学报,2004,25(4):96-100
|
CSCD被引
12
次
|
|
|
|
|
13.
马德坤.
牙轮钻头工作力学,2009
|
CSCD被引
5
次
|
|
|
|
|
了解气象卫星更多信息，请访问