热等静压/热处理工艺对激光选区熔化成形GH4169合金微观组织与拉伸性能的影响
Effects of hot isostatic pressing and heat treatment process on microstructure and tensile properties of selective laser melting manufactured GH4169alloy
查看参考文献19篇
|
文摘
|
采用激光选区熔化(SLM)成形技术制备GH4169合金,利用金相显微镜(OM)、扫描电子显微镜(SEM)、电子背散射衍射(EBSD)和透射电镜(TEM)等分析热等静压/热处理工艺对SLM成形GH4169合金微观组织及拉伸性能的影响规律。结果表明:沉积态合金组织中,沿沉积方向的晶粒为柱状晶,晶粒内枝晶组织细小,枝晶间分布大量Laves相;经热等静压后,合金中的气孔及Laves相可被有效消除,沿沉积方向的晶粒转变为等轴晶;经980℃/1h固溶处理后,合金中的晶界处析出大量短棒状δ相。热等静压/热处理后GH4169合金试样的室温及650℃拉伸性能均高于锻件标准要求的力学性能指标,且温度对断裂方式影响不大。 |
|
其他语种文摘
|
GH4169alloys were manufactured by selective laser melting(SLM).The microstructure evolution and tensile properties of GH4169alloys during hot isostatic pressing(HIP)and heat treatment(HT)process were analyzed by OM,SEM,EBSD and TEM.The results show that the grains of the as-deposited samples in the building direction are columnar,exhibit very fine cellulardendritic structure with fine Laves phases precipitating in the interdendritic region.Most of porosities and Laves phases disappear after HIP,and the microstructure parallel to the building direction is transformed into equiaxed grains.Short rod-likeδphases are precipitated along grain boundaries after annealing at 980℃for 1h.The tensile properties at room temperature and 650℃of specimens after HIP and HT are higher than those of the standard requirements for the forgings,and the temperature has a little influence on the fracture mode. |
|
来源
|
材料工程
,2020,48(6):148-155 【核心库】
|
|
DOI
|
10.11868/j.issn.1001-4381.2019.000416
|
|
关键词
|
激光选区熔化成形
;
GH4169
;
热等静压
;
组织演变
;
拉伸性能
|
|
地址
|
1.
中国航发上海商用航空发动机制造有限责任公司, 上海, 201306
2.
中国科学院金属研究所, 沈阳材料科学国家研究中心, 沈阳, 110016
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1001-4381 |
|
学科
|
金属学与金属工艺 |
|
基金
|
民用飞机专项科研资助项目
|
|
文献收藏号
|
CSCD:6748769
|
参考文献 共
19
共1页
|
|
1.
齐欢. INCONEL 718(GH4169)高温合金的发展与工艺.
材料工程,2012(8):92-100
|
CSCD被引
51
次
|
|
|
|
|
2.
娄学明. IN718高温合金热腐蚀行为及其对力学性能的影响.
稀有金属材料与工程,2008,37(2):259-263
|
CSCD被引
18
次
|
|
|
|
|
3.
Li X. Effect of heat treatment on microstructure evolution of Inconel 718alloy fabricated by selective laser melting.
Journal of Alloys and Compounds,2018,764:639-649
|
CSCD被引
16
次
|
|
|
|
|
4.
Deng D Y. Microstructure and mechanical properties of Inconel 718processed by selective laser melting:sample orientation dependence and effects of post heat treatments.
Materials Science and Engineering:A,2018,713:294-306
|
CSCD被引
30
次
|
|
|
|
|
5.
邓晓阳.
热处理对3D打印Inconel 718合金组织和力学性能的影响研究,2017
|
CSCD被引
1
次
|
|
|
|
|
6.
Sui S. The failure mechanism of 50%laser additive manufactured Inconel 718and the deformation behavior of Laves phases during a tensile process.
The International Journal of Advanced Manufacturing Technology,2017,91(5/8):2733-2740
|
CSCD被引
15
次
|
|
|
|
|
7.
明宪良. 激光修复GH4169高温合金的持久断裂机制研究.
中国激光,2015,42(4):1-7
|
CSCD被引
2
次
|
|
|
|
|
8.
Atkinson H V. Fundamental aspects of hot isostatic pressing:an overview.
Metallurgical and Materials Transactions A,2000,31(12):2981-3000
|
CSCD被引
46
次
|
|
|
|
|
9.
Kim M T. Effect of HIP process on the micro-structural evolution of a nickel-based superalloy.
Materials Science and Engineering:A,2006,441(1/2):126-134
|
CSCD被引
15
次
|
|
|
|
|
10.
Tillmann W. Hot isostatic pressing of IN718components manufactured by selective laser melting.
Additive Manufacturing,2017,13:93-102
|
CSCD被引
21
次
|
|
|
|
|
11.
Hebert R J. Viewpoint:metallurgical aspects of powder bed metal additive manufacturing.
Journal of Materials Science,2016,51(3):1165-1175
|
CSCD被引
14
次
|
|
|
|
|
12.
Tan J H. An overview of powder granulometry on feedstock and part performance in the selective laser melting process.
Additive Manufacturing,2017,18:228-255
|
CSCD被引
26
次
|
|
|
|
|
13.
Kurz W.
Fundamentals of solidification. 4th ed,1998
|
CSCD被引
5
次
|
|
|
|
|
14.
Basak A. Additive manufacturing of single-crystal superalloy CMSX-4through scanning laser epitaxy: computational modeling,experimental process development, and process parameter optimization.
Metallurgical and Materials Transactions A,2016,47(8):3845-3859
|
CSCD被引
6
次
|
|
|
|
|
15.
Fu S H. Alloy design and development of INCONEL718type alloy.
Materials Science and Engineering:A,2009,499(1/2):215-220
|
CSCD被引
23
次
|
|
|
|
|
16.
凌斌. GH169合金的相变研究.
航空材料学报,1994,14(4):1-7
|
CSCD被引
9
次
|
|
|
|
|
17.
Azadian S. Delta phase precipitation in Inconel 718.
Materials Characterization,2004,53(1):7-16
|
CSCD被引
58
次
|
|
|
|
|
18.
张善勇. 铸造高温合金的热等静压致密化机理.
钢铁研究学报,1985,5(增刊1):77-83
|
CSCD被引
3
次
|
|
|
|
|
19.
刘东. GH4169合金热加工过程中的显微组织演化数学模型~①.
中国有色金属学报,2003,13(5):1211-1218
|
CSCD被引
9
次
|
|
|
|
|
了解气象卫星更多信息，请访问