ITER校正场线圈圆弧段真空压力浸渍充模数值模拟与实验
Simulation and Experimental Study of Vacuum Pressure Impregnation for Correction Coil of International Thermonuclear Experimental Reactor
查看参考文献14篇
|
文摘
|
为优化国际热核聚变实验堆校正场线圈的真空压力浸渍工艺,对线圈圆弧段的充模过程进行了基于Darcy定律的数值模拟和工艺实验。对比了4种注胶方案的流动前沿和压力分布,确定了高效并能减少残留空隙的方案。优化的注胶口位置为沿长度方向1/4和3/4处,出胶口位置为沿长度方向两端和中间处。按优化工艺进行了试验,实测充模时间7.62×10~3 s,与模拟时间7.67×10~3 s接近。CT扫描显示试样内部被树脂完全填充,仅有少量空隙,大小约为100?200μm。试样绝缘性能优良,在10 kV下漏电流小于1 μA。试验结果表明了工艺模拟的可靠性,模拟方法可应用到整个线圈中,确定方案和技术参数。 |
|
其他语种文摘
|
The mold-filling in the arc of correction coil by vacuum pressure impregnation for International Thermonuclear Experimental Reactor was physically modeled on the basis of Darcy law, numerically simulated, and experimentally evaluated. The influence of the impregnation conditions,including but not limited to the flow front,pressure distribution, viscosity of resin, locations of inlets and outlets, and filling time in the four injection methods, on the filling efficiency were investigated. With the inlets positioned at 1/4 L and 4/3 L and with the outlets located at the center and the two ends along the axial direction,effective filling with considerable reduction of void was achieved. The simulated and measured filling times were found to be 7.67 × 10~3 s, and 7.62 × 10~3 s, respectively. Only a few small voids, 100 ?200 μm in size, were observed in computed tomography scanning of the highly insulated sample with a leakage current lower than 1 μA at 10kV. |
|
来源
|
真空科学与技术学报
,2015,35(2):225-230 【扩展库】
|
|
关键词
|
校正场线圈
;
真空压力浸渍
;
Darcy定律
;
数值模拟
|
|
地址
|
中国科学院等离子体物理研究所, 合肥, 230031
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1672-7126 |
|
学科
|
一般工业技术 |
|
基金
|
国家科技计划ITER计划专项
;
国家自然科学基金项目
|
|
文献收藏号
|
CSCD:5366157
|
参考文献 共
14
共1页
|
|
1.
黄道明. 复合材料构件真空气密性能的提升技术研究.
真空科学与技术学报,2013,33(8):744-750
|
CSCD被引
3
次
|
|
|
|
|
2.
崔益民. TU—7U纵场磁体的真空压力浸渍.
真空科学与技术学报,2002,22(3):217-220
|
CSCD被引
2
次
|
|
|
|
|
3.
Lam Y C. Numerical Simulation of the Mould-Filling Process in Resin-Transfer Moulding.
Composites Science and Technology,2000,60(6):845-855
|
CSCD被引
10
次
|
|
|
|
|
4.
Antonelli D. Resin Transfer Moulding: Mathematical Modelling and Numerical Simulations.
Composites Part A: Applied Science and Manufacturing,1999,30(12):1367-1385
|
CSCD被引
4
次
|
|
|
|
|
5.
Cairnsa Douglas S. Modeling of Resin Transfer Molding of Composite Materials with Oriented Unidirectional Plies.
Composites Part A: Applied Science and Manufacturing,1999,30(3):375-383
|
CSCD被引
5
次
|
|
|
|
|
6.
Mylene Deleglise. Solution to Filling Time Prediction Issues for Constant Pressure Driven Injection in RTM.
Composites Part A: Applied Science and Manufacturing,2005,36(3):339-344
|
CSCD被引
1
次
|
|
|
|
|
7.
Jiang Shunliang. Optimum Arrangement of Gate and Vent Locations for RTM Process Design Using a Mesh Distance-Based Approach.
Composites Part A: Applied Science and Manufacturing,2002,33(4):471-481
|
CSCD被引
2
次
|
|
|
|
|
8.
Schell J S U. Numerical Prediction and Experimental Characterisation of Meso-Scale-Voids in Liquid Composite Moulding.
Composites Part A: Applied Science and Manufacturing,2007,38(12):2460-2470
|
CSCD被引
4
次
|
|
|
|
|
9.
Laurenzi S. Process Simulation for a Large Composite Aeronautic Beam by Resin Transfer Molding.
Composites Part B:Engineering,2014,57:47-55
|
CSCD被引
5
次
|
|
|
|
|
10.
陈萍. 铺层方式对织物渗透率的影响.
复合材料学报,2001,18(1):30-33
|
CSCD被引
27
次
|
|
|
|
|
11.
Naik N K. Permeability Characterization of Polymer Matrix Composites by RTM/VARTM.
Progress in Aerospace Sciences,2014,65(2):22-40
|
CSCD被引
6
次
|
|
|
|
|
12.
Liu Baichen. Modelling and Simulation of Resin Transfer Moulding (RTM)-Gate Control, Venting and Dry Spot Prediction.
Composites Part A: Applied Science and Manufacturing,1999,27(2):135-141
|
CSCD被引
7
次
|
|
|
|
|
13.
邱婧婧. RTM工艺参数对树脂充模过程影响的模拟与实验研究.
复合材料学报,2004,21(6):70-74
|
CSCD被引
23
次
|
|
|
|
|
14.
孙玉敏. 风机叶片RTM工艺模拟分析及其优化.
复合材料学报,2005,22(4):23-29
|
CSCD被引
10
次
|
|
|
|
|
了解气象卫星更多信息，请访问