不同热处理工艺对K4169高温合金组织和力学性能的影响
Effect of different heat treatment processes on microstructure and mechanical properties of K4169 superalloy
查看参考文献22篇
|
文摘
|
对比研究标准热处理(SHT) 、热等静压+标准热处理(HIP+SHT)以及热等静压+无均匀化热处理(HIP+HTWH)后K4169合金的组织和力学性能,分析K4169合金HIP后进行无均匀化热处理的可行性,提出了一种适用于热等静压K4169合金的热处理制度。组织研究表明:热等静压处理(1170 ℃/140 MPa/4 h)可以基本消除枝晶间Laves相和δ相;而与HIP+SHT试样相比,无均匀化热处理的试样(HIP+HTWH)晶界上析出了不连续短棒状δ相,但没有对组织的均匀性产生实质影响。力学性能研究表明:相比SHT态,HIP+SHT与HIP+HTWH态合金的室温屈服强度分别提升了73 MPa和91 MPa,持久寿命(704 ℃/448 MPa)分别提升了35%和32%;虽HIP+HTWH态合金的持久寿命和塑性分散度大于HIP+SHT态,但仍能满足AMS5383对K4169合金力学性能的要求。综合考虑工艺成本的降低、生产效率的提高和力学性能的改善等多种因素,可以确定对于K4169合金结构件而言,HIP+HTWH热处理工艺具有实际应用的潜力。 |
|
其他语种文摘
|
The microstructure and mechanical properties of different heat-treated K4169 alloys after standard heat treatment (SHT), hot isostatic pressing + standard heat treatment (HIP + SHT) and hot isostatic pressing + heat treatment without homogenization (HIP + HTWH) were compared. The feasibility of heat treatment without homogenization of K4169 alloy after HIP was analyzed. A suitable heat treatment system for casting K4169 alloy was proposed. The results on microstructure show that the hot isostatic pressing (1170 °C/140 MP/4 h) can basically eliminate the Laves phase and δ phase of the alloy. Compared with the alloys after HIP + SHT, discontinuous short rod-like δ phase is existed at some grain boundaries of the sample without homogenization heat treatment (HIP + HTWH), which has no substantial influence on the uniformity of microstructure. The results on mechanical properties show that compared with the alloys after SHT, the yield strength at room temperature of alloys after HIP + SHT and HIP + HTWH is increased by 73 MPa and 91 MPa, and the stress-rupture life (704 °C/448 MPa) is increased by 35% and 32% respectively. Although the dispersion of stress-rupture life and plasticity for alloys after HIP + HTWH are higher than that of HIP + SHT, the mechanical properties meet the requirements of AMS5383 for K4169 alloy. The HIP+HTWH heat treatment process has the practical application potential for K4169 alloy structure by comprehensive analysis of various factors such as reduction of process cost, the increase of production efficiency and the improvement of mechanical properties. |
|
来源
|
航空材料学报
,2021,41(4):119-127 【核心库】
|
|
DOI
|
10.11868/j.issn.1005-5053.2021.000030
|
|
关键词
|
K4169
;
热等静压
;
无均匀化热处理
;
显微组织
;
力学性能
|
|
地址
|
1.
中国航发北京航空材料研究院先进高温结构材料重点实验室, 北京, 100095
2.
北京科技大学, 钢铁共性技术协同创新中心;;北京材料基因工程高精尖创新中心, 北京, 100083
3.
齐鲁工业大学(山东省科学院)新材料研究所, 山东省轻质高强金属材料省级重点实验室, 济南, 250014
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1005-5053 |
|
学科
|
金属学与金属工艺 |
|
文献收藏号
|
CSCD:7041423
|
参考文献 共
22
共2页
|
|
1.
Radavich J F. Effects of long time exposure in alloy 625 at 1200 F, 1400 F and 1600 F.
proceedings of the International Symposium on Superalloys 718, 625, 706 and Various Derivatives,1994:635-647
|
CSCD被引
3
次
|
|
|
|
|
2.
《工程材料实用手册》委员会.
工程材料实用手册:变形和铸造高温合金. (第2版),2002
|
CSCD被引
1
次
|
|
|
|
|
3.
Ling Li S B. Study of microsegregation and Laves phase in Incone1718 superalloy regarding cooling rate during solidification.
Metallurgical and Materials Transactions A,2015,46(1):354-361
|
CSCD被引
10
次
|
|
|
|
|
4.
中国金属学会高温材料分会.
中国高温合金手册:下卷,2012
|
CSCD被引
2
次
|
|
|
|
|
5.
王建明.
镍基铸造高温合金,2014
|
CSCD被引
5
次
|
|
|
|
|
6.
李波. K4169合金大型薄壁铸件热等静压试验.
铸造,2016,65(12):1206-1209
|
CSCD被引
2
次
|
|
|
|
|
7.
许文勇. 热等静压气氛对铸造高温合金K4169微观组织的影响.
稀有金属,2020,44(4):363-369
|
CSCD被引
5
次
|
|
|
|
|
8.
李爱兰. 热处理工艺对K4169合金微观组织的影响.
航空材料学报,2006,26(3):311-312
|
CSCD被引
16
次
|
|
|
|
|
9.
王恺. 热等静压对K4169高温合金组织与性能的影响.
中国有色金属学报,2014,24(5):1224-1231
|
CSCD被引
9
次
|
|
|
|
|
10.
李相辉. 均匀化温度对K4169合金显微组织和持久性能的影响.
稀有金属材料与工程,2014,43(1):199-203
|
CSCD被引
5
次
|
|
|
|
|
11.
李相辉. K4169合金热处理组织和性能研究.
钢铁研究学报,2011,23(增刊2):427-430
|
CSCD被引
1
次
|
|
|
|
|
12.
凌李石保. 热处理对热等静压K4169合金组织及高温持久性的影响.
特种铸造及有色合金,2016,36(10):1013-1018
|
CSCD被引
3
次
|
|
|
|
|
13.
Bocanegra-Bernal M H. Hot isotropic pressing ( HIP) technology and its applications to metals and ceramics.
J Mater Sci,2004,39:6399
|
CSCD被引
20
次
|
|
|
|
|
14.
Apparao G. Effect of standard heat treatment on the microstructure and mechanical properties of hot isostatically pressed superalloy Inconel 718.
Materials Science and Engineering: A,2003,355(1/2):114-125
|
CSCD被引
55
次
|
|
|
|
|
15.
孙艳容.
不同热处理制度对Inconel 718合金组织和性能的影响,2018
|
CSCD被引
1
次
|
|
|
|
|
16.
何树先. 热等静压处理对K4169高温合金显微形貌及性能的影响.
铸造技术,2013,34(12):1646-1648
|
CSCD被引
2
次
|
|
|
|
|
17.
张联盟.
材料科学基础,2008:464-467
|
CSCD被引
2
次
|
|
|
|
|
18.
Leo Prakash D G. Crack growth micro-mechanisms in the IN718 alloy under the combined influence of fatigue,creep and oxidation.
International Journal of Fatigue,2009,31:1966-1967
|
CSCD被引
19
次
|
|
|
|
|
19.
Jackson M P. Heat treatment of UDIMET 720Li: the effect of microstructure on properties.
Materials Science & Engineering:A,1999,259(1):85-97
|
CSCD被引
75
次
|
|
|
|
|
20.
Chen W. On the mechanism of serrated deformation in aged Inconel 718.
Materials Science and Engineering:A,1997,229:163-168
|
CSCD被引
6
次
|
|
|
|
|
了解气象卫星更多信息，请访问