SiC泡沫陶瓷/球墨铸铁双连续相复合材料的气固两相流冲蚀性能
Erosion Performance for Co-continuous Phase Composite of SiC Foam Ceramic/Ductile Iron
查看参考文献23篇
|
文摘
|
将SiC泡沫陶瓷氧化后用挤压铸造法制备了SiC泡沫陶瓷/球墨铸铁(DI)双连续相复合材料(SiC_(foam)/DI)。使用气固两相流冲蚀磨损试验机对比研究了冲蚀时间(t)、粒子速度(ν)和冲蚀角度(α)对SiC颗粒/球墨铸铁复合材料(SiC_p/DI)、SiC_(foam)/DI复合材料和DI冲蚀性能的影响,并分析了冲蚀机理。结果表明:随着冲蚀时间的增加三种材料的冲蚀速率逐渐减小并趋于稳定;随着粒子冲击速度的提高DI的冲蚀速率逐渐增加,冲蚀速率与ν2.95成正比;在冲击速度小于87.5 m/s时SiC_p/DI和SiC_(foam)/DI复合材料的冲蚀速率相近,冲击速度大于87.5 m/s时SiC_p/DI复合材料的冲蚀速率明显地比SiC_(foam)/DI复合材料的高。随着冲蚀角度的增大DI呈现出脆性材料的冲蚀特征,SiC_p/DI和SiC_(foam)/DI表现出典型的塑性材料的冲蚀特征,最大冲蚀速率对应的冲蚀角为45°。低角度时DI的冲蚀机理为微切削,高角度时为冲蚀坑和微裂纹。用高速粒子冲击时,由于SiC泡沫陶瓷的整体增强作用和阴影保护效应,SiC_(foam)/DI比SiCP/DI和DI具有更高的抗冲蚀磨损性能。 |
|
其他语种文摘
|
Co-continuous phase composite of SiC foam ceramic/ductile iron (DI) (SiC_(foam)/DI) was prepared by extrusion casting with the oxidized SiC foam ceramic as reinforcer, while the bare DI and composite of SiCparticles/ID were taken as comparison. The gas-solid two-phase flow induced erosion behavior of the three materials was assessed via a home-made gas-solid two-phase flow erosion tester, so that to reveal the effect of the erosion time (t), particle velocity (ν) and erosion angle (α), as well as the relevant erosion mechanisms. The results show that with the increasing erosion time, the erosion rate of the three materials decreased gradually and then down to a stable level. With the increase of particle impact velocity the erosion rate of DI increased gradually, and the erosion rate is proportional to ν2.95. While composites of SiCParticles/DI and SiC_(foam)/DI had similar erosion rates when the impact velocity was less than 87.5 m/s. When the impact velocity was greater than 87.5 m/s, the erosion rate of SiCParticles/DI was significantly higher than that of SiC_(foam)/DI. With the increase of erosion angle, DI exhibited erosion characteristics of brittle material, but SiCParticles/DI and SiC_(foam)/DI composites exhibited typical erosion characteristics of plastic material. The maximum erosion rate corresponded to the erosion angle 45°. The erosion mechanism of DI was micro-cutting at low angle, while erosion pitting and micro-cracking at high angle. For high-speed particle impact, SiC_(foam)/DI composite had better erosion-and wear-resistance than that of SiCParticles/DI composite and DI due to the overall reinforcement and shadow protection of SiC foam ceramics. |
|
来源
|
材料研究学报
,2020,34(5):361-367 【核心库】
|
|
DOI
|
10.11901/1005.3093.2019.167
|
|
关键词
|
复合材料
;
气固两相流
;
冲蚀磨损
;
SiC泡沫陶瓷/球墨铸铁
|
|
地址
|
1.
中国科学院金属研究所, 沈阳, 110016
2.
中国科学技术大学材料科学与工程学院, 沈阳, 110016
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1005-3093 |
|
学科
|
一般工业技术 |
|
基金
|
国家高技术研究发展计划
|
|
文献收藏号
|
CSCD:6736219
|
参考文献 共
23
共2页
|
|
1.
Praveen A S. Optimization and erosion wear response of NiCrSiB/WC-Co HVOF coating using Taguchi method.
Ceram. Int,2016,42(1):1094
|
被引
1
次
|
|
|
|
|
2.
Rawat A. Erosion wear studies on high concentration fly ash slurries.
Wear,2017,378/379:114
|
被引
1
次
|
|
|
|
|
3.
邱常明. 耐磨金属材料的最新研究进展.
甘肃冶金,2007,29(2):1-3,7
|
被引
4
次
|
|
|
|
|
4.
Du J. Numerical simulation of mold filling process for high chromium cast iron matrix composite reinforced by ZTA ceramic particles.
Int. J. Heat Mass Tran,2015,89:872
|
被引
5
次
|
|
|
|
|
5.
Sui Y D. Characterization of interfacial layer of ZTA ceramic particles reinforced iron matrix composites.
J. Alloys Compd,2018,741:1169
|
被引
4
次
|
|
|
|
|
6.
Zhou M J. Wear resistance mechanism of ZTAP/HCCI composites with a honeycomb structure.
Metals,2018,8(8):1
|
被引
1
次
|
|
|
|
|
7.
位兴民.
双连续相Ti_3AlC_2/Cu复合材料的制备及摩擦学性能研究,2016
|
被引
1
次
|
|
|
|
|
8.
Cree D. Dry wear and friction properties of an A356/SiC foam interpenetrating phase composite.
Wear,2011,272(1):88
|
被引
8
次
|
|
|
|
|
9.
Jiang L. Thermal analysis for brake disks of SiC/6061 A1 alloy co-continuous composite for CRH3 during emergency braking considering airflow cooling.
Trans. Nonferrous Met. Soc,2012,22(11):2783
|
被引
19
次
|
|
|
|
|
10.
Jiang L. Experimental study and numerical analysis on dry friction and wear performance of co-continuous SiC/Fe-40Cr against SiC/2618 Al alloy composites.
Trans. Nonferrous Met. Soc,2012,22(12):2913
|
被引
9
次
|
|
|
|
|
11.
Wang B. Effect of porous Si_3N_4 preform on the mechanical properties of Si_3N_4/Al composites with interpenetrating network structure.
Mater. Sci. Eng. A,2014,607(23):307
|
被引
1
次
|
|
|
|
|
12.
Lu Y. The mechanical properties of co-continuous Si_3N_4/Al composites manufactured by squeeze casting.
Mater. Sci. Eng. A,2010,527(23):6289
|
被引
8
次
|
|
|
|
|
13.
Wang L F. Co-Continuous Composite Materials for Stiffness, Strength, and Energy Dissipation.
Adv. Mater,2011,23(13):1524
|
被引
5
次
|
|
|
|
|
14.
Liu Q. Fabrication of a new SiC/2024Al co-continuous composite with lamellar microstructure and high mechanical properties.
J. Alloys and Comp,2014,585:146
|
被引
17
次
|
|
|
|
|
15.
杜奇. 双连续Si_3N_4/1Cr18Ni9Ti复合材料的制备和冲蚀性能.
材料研究学报,2019,33(1):34
|
被引
1
次
|
|
|
|
|
16.
陈亮.
三维网络结构SiC/Fe基复合材料的制备工艺和性能研究,2018
|
被引
1
次
|
|
|
|
|
17.
Zhong Z H. Microstructure and mechanical properties of diffusion bonded SiC/steel joint using W/Ni interlayer.
Mater. Des,2010,33(3):1070
|
被引
3
次
|
|
|
|
|
18.
Prabhu T R. Effect of SiC volume fraction and size on dry sliding wear of Fe/SiC/graphite hybrid composites for high sliding speed applications.
Wear,2014,309(1/2):1
|
被引
6
次
|
|
|
|
|
19.
Tang W M. Control of the interface reaction between silicon carbide and iron.
Mater. Chem. Phys,2003,80(1):360
|
被引
9
次
|
|
|
|
|
20.
任志恒. SiC泡沫陶瓷/Fe 基双连续相复合材料的制备和性能.
材料研究学报,2014,28(11):814
|
被引
5
次
|
|
|
|
|
了解气象卫星更多信息，请访问