300M钢激光熔覆耐磨防腐自润滑涂层温度场数值模拟研究
Numerical simulation of temperature field of wear-resistant anti-corrosion laser cladding self-lubricating coating on 300M super-strength steel
查看参考文献23篇
|
文摘
|
为了提高飞机起落架减震支柱300M超高强钢的抗磨性能,突破由于温度梯度过大诱发的激光熔覆耐磨防腐自润滑涂层裂纹等技术瓶颈,基于ANSYS软件的生死单元法编制热循环程序,考虑自润滑相和耐磨相材料热物性参数随温度的变化、相变潜热、激光熔覆过程中与外界的换热、激光熔覆功率、激光熔覆扫描速率等因素对激光熔覆过程温度场、熔池、温度梯度的影响,建立300M超高强钢激光熔覆耐磨防腐自润滑涂层温度仿真模型。结果表明:基体的熔化需要激光、熔化的粉末等综合作用使传导到该区域的有效能量达到熔化的临界值,熔化高度增加率随激光功率的增加先降低后增加,熔化高度减少率随激光扫描速率的增加先变小后变大;由于激光熔覆的不同区域温度、冷却速率差异等综合因素影响,熔覆层熔池的纵截面为勺状熔池;伴随激光功率的增加,由于熔覆层不同区域对能量输入产生的温度响应速率差异导致Z方向温度梯度值增加,且最大冷却速率增加;伴随激光扫描速率的增加,激光输入能量降低,降低了高温区域温度及激光的快速局部加热等综合影响,Z方向温度梯度值降低。通过调控激光参数,在保持熔覆层结合强度的条件下,基体熔凝区能被控制到最小,并能够降低温度梯度。 |
|
其他语种文摘
|
In order to improve the anti-wear properties of 300M super-strength steel for aircraft landing gear shock absorbing strut, and to break through the technical bottleneck such as cracks induced by the excessive temperature gradient in laser cladding wearresistant anti-corrosion self-lubricating coating, the "birth and death" method and the APDL procedure of ANSYS were used to simulate the molten pool's thermal cycle for the 300M super-strength steel's laser cladding wear-resistant anti-corrosion selflubricating coating. The change of thermophysical parameters with different temperatures for self-lubricant and wear-resistant materials, latent heat in phase change, external heat exchange during laser cladding, laser cladding power, laser cladding scanning velocity and other factors, which affect the temperature field, molten pool, temperature gradient during the laser cladding process were considered. The results indicate that the melting of the substrate requires a combination of laser and molten powder, etc. to bring the effective energy conducted to the region reach the critical value of melting, the increase rate of the melting height of the substrate decreases first and then increases with the increase of the laser power, the decrease rate of the melting height of the substrate decreases first and then becomes larger with the increase of the laser scanning speed. Due to the comprehensive factors of different temperatures and cooling rates in different laser cladding areas, the vertical section of the laser cladding wear-resistant anticorrosion self-lubricating coating bath is a spoon-shaped molten pool. With the increase of the laser power, due to the difference in the temperature response of the energy input to different regions of the cladding layer, the temperature gradient in the Z-direction and the maximum cooling rate increases. With the increase of laser scanning velocity, the laser input energy decreases, which decreases the combined effects of high-temperature region temperature and rapid local heating of the laser. Meanwhile, the temperature gradient in the Z-direction decreases. Under the condition of maintaining the bonding strength of the cladding layer, the substrate melting zone can be controlled to minimize and lower the temperature gradient by controlling laser parameters reasonably. |
|
来源
|
航空材料学报
,2020,40(2):35-42 【核心库】
|
|
DOI
|
10.11868/j.issn.1005-5053.2019.000051
|
|
关键词
|
激光熔覆
;
自润滑
;
300M钢
;
温度梯度
|
|
地址
|
中国民航大学 机场学院, 天津, 300300
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1005-5053 |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家自然科学基金
;
中央高校基本科研业务费项目中国民航大学专项资助
;
中国民航大学蓝天青年科研资金资助项目
|
|
文献收藏号
|
CSCD:6680365
|
参考文献 共
23
共2页
|
|
1.
李寒松. 300M钢表面无裂纹电镀硬铬的显微硬度和耐腐蚀性研究.
电加工与模具,2015(2):61-65
|
被引
2
次
|
|
|
|
|
2.
周克崧. 超音速火焰喷涂WC涂层替代电镀硬铬:疲劳和摩擦磨损性能.
中国工程科学,2009,11(10):48-54
|
被引
10
次
|
|
|
|
|
3.
张智慧. 300M钢超音速火焰喷涂WC涂层工艺分析.
航空制造技术,2015(增刊2):135-137
|
被引
1
次
|
|
|
|
|
4.
刘丰刚. 激光修复300M钢的组织及力学性能研究.
金属学报,2017,53(3):325-334
|
被引
12
次
|
|
|
|
|
5.
Liu F. Effect of tempering temperature on microstructure and mechanical properties of laser solid formed 300 M steel.
Journal of Alloys and Compounds,2016,689:225-232
|
被引
4
次
|
|
|
|
|
6.
钟平.
超高强度钢组织、性能与腐蚀行为,2014
|
被引
3
次
|
|
|
|
|
7.
Liu X B. Development and characterization of laser clad high temperature self-lubricating wear resistant composite coatings on Ti-6Al-4V alloy.
Materials and Design,2014(55):404-409
|
被引
8
次
|
|
|
|
|
8.
张春燕. 激光熔凝稀土镁合金温度场的数值模拟及其耐蚀性能.
热加工工艺,2017(2):143-147
|
被引
4
次
|
|
|
|
|
9.
Zhou Z Y. Laser in-situ synthesizing Ti5Si3/Al3Ni2 reinforced Al3Ti/NiTi composite coatings: microstructure, mechanical characteristics and oxidation behavior.
Optics and Laser Technology,2019(109):99-109
|
被引
1
次
|
|
|
|
|
10.
孟云龙. 激光熔凝对AerMet100钢显微组织及性能的影响.
激光与光电子学进展,2018,55(2):021414
|
被引
8
次
|
|
|
|
|
11.
牛伟. h-BN含量对激光熔覆自润滑涂层微观组织和磨损性能的影响.
中国激光,2011,38(8):126-132
|
被引
4
次
|
|
|
|
|
12.
任良帅. 镍包石墨自润滑涂层的制备及性能.
材料热处理学报,2018,39(12):97-102
|
被引
1
次
|
|
|
|
|
13.
马少海. Co元素对300M钢组织和性能的影响.
金属热处理,2015,40(7):120-124
|
被引
2
次
|
|
|
|
|
14.
刘锐. Crl2MoV钢表面激光熔覆Co/MoS_2/CaF_2涂层研究.
应用激光,2016,36(3):247-252
|
被引
1
次
|
|
|
|
|
15.
Roberts I A. A three-dimensional finite element analysis of the temperature field during laser melting of metal powders in additive layer manufacturing.
International Journal of Machine Tools & Manufacture,2009,49(12/13):916-923
|
被引
26
次
|
|
|
|
|
16.
Balu P. Finite element modeling of heat transfer in single and multilayered deposits of Ni-WC produced by the laser-based powder deposition process.
The International Journal of Advanced Manufacturing Technology,2013,68(1/2/3/4):85-98
|
被引
1
次
|
|
|
|
|
17.
杨世铭.
传热学. (第四版),2015:115-121
|
被引
1
次
|
|
|
|
|
18.
陈智. 基于 SYSWELD 的预热温度对焊接热输入影响的有限元模拟.
热加工工艺,2014(15):164-166
|
被引
2
次
|
|
|
|
|
19.
陈华.
300 M钢热处理晶粒度变化的实验研究及数值模拟. (5),2016:21-26
|
被引
1
次
|
|
|
|
|
20.
彭旭东. 聚醚醚酮基复合材料的热性质和物理性质预测及其摩擦销三维温度场的数值模拟.
摩擦学学报,2005,25(4):354-365
|
被引
2
次
|
|
|
|
|
了解气象卫星更多信息，请访问