氧化膜对6082铝合金搅拌摩擦焊接头疲劳性能的影响
Influence of Oxide Film on Fatigue Property of Friction Stir Welded 6082 Al Alloy
查看参考文献20篇
|
文摘
|
对6 mm厚的6082-T6铝合金进行两种表面处理然后实施搅拌摩擦焊接,研究了对接面氧化膜对接头组织和疲劳性能的影响。结果表明,进行速度为1000 mm/min的高速焊接时,对接面未打磨和打磨的接头焊接质量都良好,接头强度系数达到81%;两种接头的疲劳性能基本相同,疲劳强度均为100 MPa;少数样品在焊核区外断裂,大部分样品在热影响区断裂。与接头相比,两种接头焊核区的疲劳性能有所提高,均为110 MPa,在疲劳测试中裂纹并未沿“S”线萌生和扩展。 |
|
其他语种文摘
|
The polished and as received 6082-T6 Al sheets of 6 mm in thickness were subjected to friction stir welding (FSW) aiming to revealthe effect of surface oxide film on the microstructure and fatigue property of the FSW joint.The results show that high quality FSW joints with a high joint strength coefficient of 81% could be produced by a high welding speed of 1000 mm/min,for the unpolished and polished butt surfaces.Similar fatigue properties were obtained for the two type of FSW joints with the above two surface states,and the fatigue strength was 100 MPa.Most weld joints failed at the heat affected zones,and only a few weld joints failed at the nugget zone (NZ) during fatigue tests.The fatigue strength increased to 110 MPa for the NZ for plates with the above two surface states,and it is revealed during fatigue test that the fatigue cracks did not initiate on and propagate along the so called“S-line”. |
|
来源
|
材料研究学报
,2019,33(4):299-305 【核心库】
|
|
DOI
|
10.11901/1005.3093.2018.625
|
|
关键词
|
金属材料
;
铝合金
;
搅拌摩擦焊接
;
氧化膜
;
疲劳性能
|
|
地址
|
1.
中车长春轨道客车股份有限公司, 长春, 130062
2.
中国科学院金属研究所, 沈阳材料科学国家研究中心, 沈阳, 110016
3.
东北大学材料科学与工程学院, 沈阳, 110819
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1005-3093 |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家自然科学基金
|
|
文献收藏号
|
CSCD:6476374
|
参考文献 共
20
共1页
|
|
1.
Mishra R S. Friction stir welding and processing.
Mater. Sci. Eng,2005,50R:1
|
被引
526
次
|
|
|
|
|
2.
王快社. 搅拌摩擦与氩弧焊铝合金接头疲劳性能比较.
材料研究学报,2009,23:1
|
被引
1
次
|
|
|
|
|
3.
薛鹏. 搅拌摩擦焊接与加工研究进展.
金属学报,2016,52:1222
|
被引
20
次
|
|
|
|
|
4.
Zhou C Z. Effect of oxide array on the fatigue property of friction stir welds.
Scripta Mater,2006,54:1515
|
被引
6
次
|
|
|
|
|
5.
Jolu T L. Effect of joint line remnant on fatigue lifetime of friction stir welded Al-Cu-Li alloy.
Sci. Technol.Weld. Joining,2010,15:694
|
被引
7
次
|
|
|
|
|
6.
Zeng X H. Effect of processing parameters on plastic flow and defect formation in friction-stir-welded aluminum alloy.
Metall. Mater. Trans. A,2018,49:2673
|
被引
8
次
|
|
|
|
|
7.
Sato Y S. FIB-assisted TEM study of an oxide array in the root of a friction stir welded aluminium alloy.
Scripta Mater,2004,50:365
|
被引
21
次
|
|
|
|
|
8.
Ren S R. Effect of initial butt surface on tensile properties and fracture behavior of friction stir welded Al-Zn-Mg-Cu alloy.
Mater. Sci. Eng. A,2008,479:293
|
被引
10
次
|
|
|
|
|
9.
Liu X Q. Correlation between microstructures and mechanical properties of high-speed friction stir welded aluminum hollow extrusions subjected to axial forces.
J. Mater. Sci. Technol,2018,34:105
|
被引
1
次
|
|
|
|
|
10.
Wang G Q. Friction stir welding of high-strength aerospace aluminum alloy and application in rocket tank manufacturing.
J. Mater. Sci. Technol,2018,34:73
|
被引
25
次
|
|
|
|
|
11.
Wang B B. Enhanced Mechanical Properties of Friction Stir Welded 5083Al-H19 Joints with Additional Water Cooling.
J. Mater. Sci. Technol,2017,33:1009
|
被引
23
次
|
|
|
|
|
12.
王希靖. 6082- T6铝合金搅拌摩擦焊组织演变与力学性能.
焊接学报,2018,39:1
|
被引
5
次
|
|
|
|
|
13.
Scialpi A. Influence of shoulder geometry on microstructure and mechanical properties of friction stir welded 6082 aluminium alloy.
Mater. Des,2007,28:1124
|
被引
14
次
|
|
|
|
|
14.
Liu F C. Influence of tool dimension and welding parameters on microstructure and mechanical properties of friction-stirwelded 6061-T651 aluminum alloy.
Metall. Mater. Trans. A,2008,39:2378
|
被引
33
次
|
|
|
|
|
15.
Wang C. High-speed friction stir welding of SiCp/Al-Mg-Si composite.
Acta Metall. Sin. (Engl. Lett.),2018
|
被引
1
次
|
|
|
|
|
16.
王晨. SiCp/6092Al复合材料搅拌摩擦焊接头的疲劳行为研究.
金属学报,2018
|
被引
1
次
|
|
|
|
|
17.
武传松. 搅拌摩擦焊接产热传热过程与材料流动的数值模拟.
金属学报,2018,54:265
|
被引
8
次
|
|
|
|
|
18.
王洪亮. 5083和6061铝合金异种搅拌摩擦焊接接头的组织和性能.
材料研究学报,2018,32:473
|
被引
4
次
|
|
|
|
|
19.
Li Y J. Tensile properties and fracture behavior of friction stir welded joints of Fe-32Mn-7Cr-l Mo-0.3N steel at cryogenic temperature.
J. Mater. Sci. Technol,2018,34:157
|
被引
3
次
|
|
|
|
|
20.
陈菲菲. 搅拌摩擦加工超细晶材料的组织和力学性能研究进展.
材料研究学报,2018,32:1
|
被引
10
次
|
|
|
|
|
了解气象卫星更多信息，请访问