炮钢表面激光熔覆Hastelloy C-276涂层的组织及性能
Microstructure and Properties of Laser Cladding Hastelloy C-276Coating on Gun Steel Surface
查看参考文献19篇
|
文摘
|
研究Hastelloy C-276激光熔覆层的组织与性能,为炮管激光修复做好基础研究工作。利用激光熔覆系统在炮管表面制备Hastelloy C-276熔覆层,采用光学显微镜(OM)、扫描电子显微镜(SEM)、显微硬度计和电化学工作站,研究其显微组织形貌、显微硬度及耐蚀性。在炮钢表面制备的Hastelloy C-276熔覆层质量良好,无明显气孔、裂纹等缺陷,厚度约为1.2 mm,组织均匀,晶粒细小,与基体结合良好。从熔覆层表面到基体的硬度分布呈先升后降趋势,熔覆层平均硬度在280HV左右,相变区硬度最高达到500HV,基体平均硬度在350HV左右。炮管原始镀铬层的自腐蚀电位为-0.734V,自腐蚀电流密度为2.39×10~(-6) A/cm~2,熔覆层试样的自腐蚀电位为-0.326V,自腐蚀电流密度为3.59×10~(-6) A/cm~2,与原始镀铬层相比,熔覆层的自腐蚀电位值正移,腐蚀电流密度值稍微偏大,但仍在同一级量。采用激光熔覆技术,能够在炮钢表面制备综合质量良好的Hastelloy C-276熔覆层,且其具有优良的耐蚀性,与基体结合良好,可以部分补足身管强度。 |
|
其他语种文摘
|
To study the microstructure and properties of the Hastelloy C-276 laser cladding layer,and to do basic research work for laser repairing gun barrel.The cladding layer of Hastelloy C-276 was prepared on the surface of the gun steel by using a laser cladding system.The microstructure morphology,microhardness and corrosion resistance of the layer were investigated with optical microscope(OM),scanning electron microscope(SEM),microhardness tester and electrochemical workstation.The Hastelloy C-276 cladding layer prepared on the surface of the gun steel was of good quality and had no obvious pores,cracks,and other defects.The thickness was about 1.2 mm,uniform structure,fine grain,and good combination with the substrate.The microhardness distribution from the surface of the cladding layer to the substrate showed a trend of rising first and then decreasing.The average microhardness of the cladding layer was about 280HV,the highest microhardness in the phase change zone was 500HV,and the average hardness of the substrate was about 350HV.The self-corrosion potential of original chrome plated gun barrel was-0.734V,the self-corrosion current density was 2.39×10~(-6) A/cm~2.The self-corrosion potential of the cladding layer sample was-0.326V,and self-corrosion current density was 3.59×10~(-6) A/cm~2.Compared with the original chrome plated gun barrel,the corrosion potential of the cladding layer shifts positively and the corrosion current density value was slightly larger,but it was still in the same level.Using laser cladding technology,a Hastelloy C-276 cladding layer with good overall quality could be prepared on the surface of the gun steel,and it had excellent corrosion resistance,and was well combined with the substrate,and could partially compensate for the strength of the tube. |
|
来源
|
应用激光
,2018,38(3):321-327 【扩展库】
|
|
DOI
|
10.14128/j.cnki.al.20183803.321
|
|
关键词
|
激光熔覆
;
Hastelloy C-276
;
炮钢
;
显微组织
;
显微硬度
;
耐蚀性
|
|
地址
|
1.
中国科学院力学研究所, 中国科学院先进制造工艺力学重点实验室, 北京, 100190
2.
河北科技大学理学院, 河北, 石家庄, 050080
3.
中国人民解放军92942部队, 北京, 100161
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1000-372X |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家自然科学基金资助项目
|
|
文献收藏号
|
CSCD:6397760
|
参考文献 共
19
共1页
|
|
1.
夏兰廷.
金属材料的海洋腐蚀与防护,2003:2-4
|
被引
1
次
|
|
|
|
|
2.
陈光章. 舰船腐蚀与防护.
舰船科学技术,2001(2):38-43
|
被引
5
次
|
|
|
|
|
3.
侯保荣. 海洋腐蚀防护的现状与未来.
中国科学院院刊,2016,31(12):1326-1331
|
被引
50
次
|
|
|
|
|
4.
岳灿甫. 激光熔覆及其在水中兵器修复上的应用.
鱼雷技术,2007,15(1):1-5
|
被引
9
次
|
|
|
|
|
5.
Ahmad M. Microstructure and hardness studies of the electron beam welded zone of Hastelloy C-276.
Journal of Alloys and Compounds,2005,309(1/2):88-93
|
被引
28
次
|
|
|
|
|
6.
Khalid S E. Comparative studies of the seawater corrosion behavior of a range of materials.
Desalination,2003,158(1/3):35-42
|
被引
13
次
|
|
|
|
|
7.
Zhang Qiang. Corrosion behavior of Hastelloy C-276in supercritical water.
Corrosion Science,2009,51(9):2092-2097
|
被引
9
次
|
|
|
|
|
8.
任冠鹏. 不同焊接方法对哈氏合金C-276焊缝组织和耐晶间腐蚀性能的影响.
材料开发与应用,2016,31(5):40-44
|
被引
2
次
|
|
|
|
|
9.
潘杰军. 哈氏合金C-276与16Mn异种合金对接焊缝射线检测.
无损检测,2013,35(8):36-43
|
被引
1
次
|
|
|
|
|
10.
Bagchi A. Numerical simulation and optimization in pulsed Nd: YAG laser welding of Hastelloy C-276through Taguchi method and artificial neural network.
Optik,2017(146):80-89
|
被引
1
次
|
|
|
|
|
11.
黄科. 超音速火焰喷涂哈氏合金C-276涂层的显微结构与性能.
材料研究与应用,2010,4(3):207-210
|
被引
2
次
|
|
|
|
|
12.
李正秋. 半导体激光熔覆与超音速火焰喷涂Ni60粉末组织与性能的研究.
热加工工艺,2017,46(20):149-151
|
被引
1
次
|
|
|
|
|
13.
胡汉起.
金属凝固原理,2000:177-190
|
被引
1
次
|
|
|
|
|
14.
张松. Monel合金表面激光熔覆镍基合金的组织及摩擦磨损性能.
焊接学报,2013,34(1):9-12
|
被引
7
次
|
|
|
|
|
15.
Basu A. Laser surface coating of Fe-Cr-Mo-Y-B-C bulk metallic glass composition on AISI 4140steel.
Surface and Coatings Technology,2008,202(12):2623-2631
|
被引
20
次
|
|
|
|
|
16.
胡肇炜. 激光熔覆原位合成Mo_2NiB_2涂层工艺研究.
表面技术,2017,46(8):1-6
|
被引
9
次
|
|
|
|
|
17.
张德强. 45#钢表面激光熔覆自熔性镍基碳化钨粉末.
表面技术,2015,44(11):66-70
|
被引
8
次
|
|
|
|
|
18.
曹楚南.
腐蚀电化学原理,2008:99-110
|
被引
9
次
|
|
|
|
|
19.
张艳. 2507双相不锈钢在NaClO溶液中的腐蚀性能.
材料工程,2016,44(1):108-114
|
被引
12
次
|
|
|
|
|
了解气象卫星更多信息，请访问