Al基金属玻璃涂层孔隙特性的精确表征及对其腐蚀行为的影响规律
Accurate Characterization for Pore Properties of Aluminum-based Metallic Class Coating and the Influence of Pores on Corrosion Behavior of Coating
查看参考文献21篇
|
文摘
|
选用Al_(86)Ni_6Y_(4.5)Co_2La_(1.5)铝基非晶粉体材料,采用自研的低温超音速喷涂系统,在ZM5表面制备了具备良好耐蚀性能的铝基金属玻璃涂层,分析了涂层的孔隙类型及成因,优选出X射线三维成像法测定了涂层孔隙率,表征了涂层孔隙几何特征,阐明了孔隙对涂层腐蚀行为的影响规律。结果表明,涂层主要包含宏观型、层间型、微球型和微细型四类常规孔隙缺陷;涂层孔隙率基本小于1%且沿厚度方向上变化不大,孔隙呈近球形,尺寸均小于10 μm,尤以5 μm左右居多;不同孔隙率的涂层均呈现出较宽的自钝化区间,自腐蚀电位较为接近,腐蚀电流密度与孔隙率正相关,大尺寸、贯穿型、边界处的个别特殊孔隙是导致涂层腐蚀失效的根本原因。 |
|
其他语种文摘
|
The aluminum-based metallic glass coating on ZM5 surface with good corrosion resistance was prepared from Al_(86)Ni_6Y_(4.5)Co_2La_(1.5) amorphous powder by self-developed low-temperature supersonic spray system. The types and causes of pores in the coating were analyzed, the porosity of the coating was determined by X-ray three-dimensional imaging method, the pore geometry features were characterized, and the influence of pores on the corrosion behavior of the coating was clarified. The results show that the coating consists mainly of four types of conventional porosity defects,which are macro-type,layer-type, microsphere-type and microscopic-type. The porosities are substantially less than 1% and have little change along the thickness direction. The pores are nearly spherical, and their average sizes are less than 10 μm, mostly about 5 μm; the coatings of different porosities show a wide range of self passivation interval,self corrosion potentials are closer,and there is a positive correlation between the corrosion current densities and porosities. Individual special pores at the border with the characteristics of large-size and through-type are the fundamental cause of corrosion failure of the coating. |
|
来源
|
稀有金属材料与工程
,2017,46(12):3779-3784 【核心库】
|
|
关键词
|
铝基金属玻璃涂层
;
低温超音速喷涂
;
X射线三维成像法
;
孔隙
;
腐蚀行为
|
|
地址
|
1.
装甲兵工程学院, 装备再制造技术国防科技重点实验室, 北京, 100072
2.
中国科学院金属研究所, 沈阳材料科学国家联合实验室, 辽宁, 沈阳, 110016
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1002-185X |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家科技部国际合作项目
;
军队计划重点基金资助项目
|
|
文献收藏号
|
CSCD:6136825
|
参考文献 共
21
共2页
|
|
1.
Yang B J.
Scripta Materialia,2009,61(4):423
|
被引
25
次
|
|
|
|
|
2.
Inoue A.
Progress in Materials Science,1998,43(5):365
|
被引
62
次
|
|
|
|
|
3.
吴学庆. Al_(88)Ni_6La_6非晶及其晶化薄带的腐蚀行为研究.
稀有金属材料与工程,2007,36(9):1668
|
被引
7
次
|
|
|
|
|
4.
Sun Z.
Materials & Design,2015,81:59
|
被引
1
次
|
|
|
|
|
5.
Yi J J.
Journal of Alloys and Compounds,2015,628:245
|
被引
2
次
|
|
|
|
|
6.
Babu P.
Materials Science & Engineering A,2016,658(1):415
|
被引
6
次
|
|
|
|
|
7.
Zhang W.
Journal of Alloys and Compounds,2016,688:89
|
被引
1
次
|
|
|
|
|
8.
Johnson W C.
Metallurgical and Materials Transactions, A,2009,40:757
|
被引
1
次
|
|
|
|
|
9.
Han F F.
Journal of Materials Science,2016:1
|
被引
1
次
|
|
|
|
|
10.
Dittrich M.
Intermetallics,2016,74:46
|
被引
1
次
|
|
|
|
|
11.
Willian C.
Metallurgical and Materials Transactions A,2009,40(4):757
|
被引
1
次
|
|
|
|
|
12.
于玮.
Dissertation for Master(硕士论文),2012
|
被引
1
次
|
|
|
|
|
13.
张志彬. 高速电弧喷涂铝基非晶纳米晶复合涂层的组织及性能.
稀有金属材料与工程,2012,41(5):872
|
被引
8
次
|
|
|
|
|
14.
张志彬. 电弧喷涂制备铝基非晶纳米晶合金材料.
北京工业大学学报,2012,38(6):933
|
被引
2
次
|
|
|
|
|
15.
张秦梁. 铝基非晶纳米晶复合涂层的喷涂工艺.
中国表面工程,2015,28(6):104
|
被引
3
次
|
|
|
|
|
16.
梁秀兵. 铝基非晶纳米晶复合涂层研究.
金属学报,2012,48(3):289
|
被引
13
次
|
|
|
|
|
17.
于惠博. 降低涂层孔隙率的研究进展.
材料导报,2007,21(1):68
|
被引
15
次
|
|
|
|
|
18.
綦建峰.
工程地质学报,2014,22:339
|
被引
4
次
|
|
|
|
|
19.
孙先达. 激光扫描共聚焦显微镜在微孔隙研究中的应用.
电子显微学报,2014,33(2):123
|
被引
10
次
|
|
|
|
|
20.
王绍钢. 高分辨透射X射线三维成像在材料科学中的应用.
金属学报,2013,49(8):897
|
被引
21
次
|
|
|
|
|
了解气象卫星更多信息，请访问