帮助 关于我们

返回检索结果

脉冲电流对再制造毛坯裂纹尖端组织及性能的影响
Effects of Pulsed Current on Microstructure and Properties of Crack Tip in Remanufacturing Blank

查看参考文献17篇

邓德伟 1 *   刘倩倩 1   李晓娜 1   于涛 2   张林 3   王罡 4   张洪潮 2  
文摘 以再制造为目标,利用高能脉冲电流冲击装置对含有单边裂纹的316奥氏体不锈钢进行脉冲电流处理。采用金相显微镜、X-射线衍射仪、电子背散射衍射(EBSD)、透射电子显微镜(TEM)等表征手段,研究高密度脉冲电流对裂纹尖端区域微观组织与结构的影响,分析裂纹尖端组织加热熔化及热处理时的组织演变过程。结果表明:脉冲电流处理后,裂纹尖端组织发生了明显细化并出现组织梯度,包括柱状晶区、再结晶区及基体区。脉冲电流的快速加热和快速冷却、高速电子风的产生、电致塑性等作用降低了再结晶或相变时的热力学屏障,提高了形核率,抑制了晶粒长大过程,获得了比原始晶粒尺寸小的再结晶晶粒,材料的力学性能得到提高。
其他语种文摘 A high energy pulsed current impacting device was used to treat 316 austenitic stainless steel containing prefabricated unilateral fatigue crack aiming for remanufacturing. The influence of high density pulsed current on the microstructure at crack tip was investigated by metallographic microscope, X-ray diffraction, electron backscattered diffraction (EBSD) and transmission electron microscope (TEM). And the evolution of microstructure during melting treatment was analyzed. Results show that the structure at crack tip is obviously refined after the pulsed current processing, and the gradient structure including the columnar crystal area, recrystallization zone and matrix is observed. Due to the rapid heating and cooling, the generation of high-speed electronic wind and electrically induced plasticity effect reduce the thermodynamic barrier of recrystallization or phase change. Thus, the rate of nucleation is increased, and the grain growth process is inhibited. Therefore the grain size of recrystallization zone is smaller than that of the matrix, and hence the mechanical properties of materials are improved.
来源 稀有金属材料与工程 ,2017,46(8):2208-2213 【核心库】
关键词 再制造 ; 脉冲电流 ; 再结晶 ; 组织细化
地址

1. 大连理工大学材料科学与工程学院, 辽宁, 大连, 116023  

2. 大连理工大学机械工程学院, 辽宁, 大连, 116023  

3. 沈阳鼓风机集团股份有限公司, 辽宁, 沈阳, 110869  

4. 清华大学, 北京, 100084

语种 中文
文献类型 研究性论文
ISSN 1002-185X
学科 金属学与金属工艺
基金 国家973计划 ;  辽宁省自然科学基金 ;  辽宁省科技创新重大专项 ;  沈鼓-大工重大科研发展基金 ;  中央高校基本科研业务费专项资金
文献收藏号 CSCD:6057975

参考文献 共 17 共1页

1.  Song P S. International Journal of Fatigue,2001,23(3):259 被引 4    
2.  王刚. 焊接,2008(1):20 被引 17    
3.  Buxbaum O. Engineering Fracture Mechanics,1987,28(5/6):689 被引 3    
4.  Goto M. Fatigue & Fracture of Engineering Materials & Structures,1996,19(1):39 被引 4    
5.  Murdani A. Engineering Failure Analysis,2008,15(4):302 被引 8    
6.  Conrad H. Materials Science and Engineering A,2000,287(2):205 被引 158    
7.  Conrad H. Scripta Metallurgica,1984,18(3):275 被引 24    
8.  Conrad H. JOM,1990,42(9):28 被引 30    
9.  白象忠. 电磁热效应裂纹止裂研究的进展. 力学进展,2000,30(4):546 被引 25    
10.  Song H. Materials Science and Engineering A,2008,490(1/2):1 被引 21    
11.  王钧石. 机械工程材料,1993,17(5):9 被引 1    
12.  Knobbe H. Procedia Engineering,2010,2(1):931 被引 5    
13.  Long M. Acta Materialia,1999,47(2):661 被引 3    
14.  Zhu R F. Journal of Alloys and Compounds,2013,581:160 被引 3    
15.  肖素红. 电脉冲处理下疲劳铜单晶的再结晶. 金属学报,2002,38(2):161 被引 7    
16.  吕宝臣. 脉冲电流对疲劳后30CrMnSiA钢组织结构的影响. 材料研究学报,2003,17(1):15 被引 9    
17.  Hosoi A. Materials,2013,6(9):4213 被引 9    
引证文献 1

1 王凯旋 微螺钉用细晶两相钛合金韧化因素及研究现状 中国材料进展,2020,39(10):776-781
被引 0 次

显示所有1篇文献

论文科学数据集
PlumX Metrics
相关文献

 作者相关
 关键词相关
 参考文献相关

版权所有 ©2008 中国科学院文献情报中心 制作维护:中国科学院文献情报中心
地址:北京中关村北四环西路33号 邮政编码:100190 联系电话:(010)82627496 E-mail:cscd@mail.las.ac.cn 京ICP备05002861号-4 | 京公网安备11010802043238号