Nb 添加对Zr_(50.5–x)Al_9Ni_(4.05)Cu_(36.45)Nb_x非晶合金热稳定性及力学性能的影响
Effect of Nb addition on thermal stability and mechanical properties of Zr_(50.5–x)Al_9Ni_(4.05)Cu_(36.45)Nb_x amorphous alloy
查看参考文献23篇
|
文摘
|
采用铜模铸造法,制备了直径为2 mm的Zr_(50.5–x)Al_9Ni_(4.05)Cu_(36.45)Nb_x(x=0,1,2,4,摩尔分数,%)完全非晶棒材。分别采用X射线衍射仪(XRD)、扫描电镜(SEM)、透射电镜(TEM)、差示扫描量热计(DSC)和力学性能试验机对合金的相组成、结构、热物性参数和力学性能进行研究。结果表明:添加Nb对所研究合金的玻璃转变温度Tg影响不大,但提高了晶化温度T_x和过冷液相区ΔT_x;当x=4时,合金具有最高的玻璃转变温度T_x=773.4 K和最大过冷液相区ΔT_x=68.1 K。依据耐温和热塑性成形要求,非晶合金的热稳定性可用玻璃转变温度T_x和过冷液相区ΔT_x来分别表示。随着合金中Nb添加量的增加,非晶合金的双重热稳定性提高。非晶合金的断裂强度随着 Nb添加量的增加先减小后增加,当x=4时,合金的最高断裂强度为2032 MPa。 |
|
其他语种文摘
|
Zr_(50.5–x)Al_9Ni_(4.05)Cu_(36.45)Nb_x(x=0, 1, 2, 4, mole fraction, %) amorphous alloy bar with 2 mm in diameter were fabricated by copper mold casting method. The phase constitution, microstructure, thermal property and mechanical properties of alloys were investigated by X-ray diffractometry (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), differential scanning calorimetry (DSC) and electronic testing machine. The results show that the effect of Nb addition on the glass transition temperature Tg of the alloys is slight. However, the crystallization temperature T_x and supercooled liquid region ΔT_x of the alloy obviously increase with increasing the Nb addition. When x is 4, the alloy has the highest glass crystallization temperature (T_x=773.4 K) and largest supercooled liquid region (ΔT_x=68.1 K). According to the demand of heat tolerance and thermoplasticity shaping, the thermal stability of amorphous alloy can be represented by T_x and ΔT_x, respectively. And for this investigated system, the thermal stability of amorphous alloy can be enhanced by increasing the Nb content. The fracture strength decreases first and then increases with increasing the Nb content, and the fracture strength reaches the highest value of 2032 MPa while x is 4. |
|
来源
|
中国有色金属学报
,2015,25(7):1876-1881 【核心库】
|
|
关键词
|
Zr_(50.5–x)Al_9Ni_(4.05)Cu_(36.45)Nb_x
;
非晶合金
;
Nb 添加
;
热稳定性
;
力学性能
|
|
地址
|
1.
沈阳工业大学材料科学与工程学院, 沈阳, 110870
2.
中国科学院金属研究所, 沈阳材料科学国家(联合)实验室, 沈阳, 110016
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1004-0609 |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家973计划
|
|
文献收藏号
|
CSCD:5504608
|
参考文献 共
23
共2页
|
|
1.
Sun Y J. Zr-Cu-Ni-Al bulk metallic glass with superhigh glass-forming ability.
Acta Materialia,2009,57:1290-1299
|
被引
12
次
|
|
|
|
|
2.
张志豪. Zr55Al10Ni5Cu30大块非晶合金的超塑性挤压成形性能.
中国有色金属学报,2005,15(1):33-37
|
被引
12
次
|
|
|
|
|
3.
胡桥. 不同形态和热历史条件下Zr_(55)Al_(10)Ni_5Cu_(30)非晶合金的晶化行为.
金属学报,2012,48(12):1467-1473
|
被引
8
次
|
|
|
|
|
4.
Zhou W. Effects of Ag addition on crystallization, microstructure and mechanical properties of Zr-Cu-Ni-Al-Ag bulk metallic glasses.
Journal of Alloys and Compounds,2013,552:102-106
|
被引
4
次
|
|
|
|
|
5.
Xing Dawei. Investigation of precipitation phases in as-cast wedge ingot of bulk amorphous Zr_(56.6)Cu_(17.3)Ni_(12.5)Al_(9.6)Ti_4 alloy.
Journal of Alloys and Compounds,2009,481:531-538
|
被引
3
次
|
|
|
|
|
6.
Xing Dawei. Evolution of the primary crystals and amorphous matrix following annealing of a bulk Zr_(56.6)Cu_(17.3)Ni_(12.5)Al_(9.6)Ti_4 metallic glass.
Materials Science and Engineering A,2009,513/514:8-12
|
被引
1
次
|
|
|
|
|
7.
Ott R T. Structure and properties of Zr-Ta-Cu-Ni-Al bulk metallic glasses and metallic glass matrix composites.
Journal of Non-Crystalline Solids,2003,317:158-163
|
被引
2
次
|
|
|
|
|
8.
Zhu Z. Ta-particulate reinforced Zr-based bulk metallic glass matrix composite with tensile plasticity.
Scripta Materialia,2010,62:278-281
|
被引
14
次
|
|
|
|
|
9.
Dong Wenbo. Zr-Cu-Ni-Al-Ta glassy matrix composites with enhanced plasticity.
Journal of Materials Research,2006,21(6):1490-1499
|
被引
5
次
|
|
|
|
|
10.
Yan Ming. Effect of over-doped yttrium on the microstructure, mechanical properties and thermal properties of a Zr-based metallic glass.
Acta Materialia,2006,54:3627-3635
|
被引
7
次
|
|
|
|
|
11.
Yan M. Cooling rate dependent as-cast microstructure and mechanical properties of Zr-based metallic glasses.
Journal of Materials Science,2007,42:4233-4239
|
被引
3
次
|
|
|
|
|
12.
Liu Guangqiao. Effect of minor Fe addition on glass forming ability and mechanical properties of Zr_(55)Al_(10)Ni_(5)Cu_(30) bulk metallic glass.
Transactions of Nonferrous Metals Society of China,2012,22:590-595
|
被引
7
次
|
|
|
|
|
13.
Deng S T. Improving glass forming ability of Zr_(50.5)Cu_(36.5)Ni_4Al_9 alloy by suppressing CuZr phase precipitation.
Journal of Alloys and Compounds,2008,460:182-185
|
被引
5
次
|
|
|
|
|
14.
Liu Jinmin. In situ spherical B_2 CuZr phase reinforced ZrCuNiAlNb bulk metallic glass matrix composite.
Journal of Materials Research,2010,25(6):1159-1163
|
被引
2
次
|
|
|
|
|
15.
Geller J S.
The Biy Genius Report: iPhone 5S to feature indestructible Liquid Metal case,2013
|
被引
1
次
|
|
|
|
|
16.
Fan Cang. Effects of Nb addition on icosahedral quasicrystalline phase formation and glass-forming ability of Zr-Ni-Cu-Al metallic glasses.
Applied Physics Letters,2001,79(7):1024-1026
|
被引
9
次
|
|
|
|
|
17.
柳林. Zr-Cu-Ni-Al-Nb大块非晶合金的晶化行为、力学性能及电化学腐蚀行为的研究.
物理学报,2006,55(4):1930-1935
|
被引
10
次
|
|
|
|
|
18.
刘广桥. Nb含量对Zr_(55)Cu_(30)Ni_5Al_(10)块体金属玻璃热稳定性和力学性能的影响.
稀有金属,2013,37(4):576-582
|
被引
3
次
|
|
|
|
|
19.
Qiu K Q. Mechanical properties and fracture mechanism of as-cast Mg_(77)TM_(12)Zn_5Y_6(TM=Cu, Ni) bulk amorphous matrix composites.
Journal of Alloys and Compounds,2009,478:419-422
|
被引
3
次
|
|
|
|
|
20.
Li Q F. Glass forming ability and reliability in fracture stress for Mg-Cu-Ni-Nd-Y bulk metallic glasses.
Materials Science and Engineering A,2008,491:420-424
|
被引
6
次
|
|
|
|
|
了解气象卫星更多信息，请访问