帮助 关于我们

返回检索结果

激光冲击强化对TiAl合金组织和性能的影响
Effect of laser peening on microstructures and properties of TiAl alloy

查看参考文献13篇

乔红超 1 *   赵亦翔 2   赵吉宾 1   陆莹 1  
文摘 为研究激光冲击强化对TiAl合金组织和性能的影响,利用波长为1 064 nm、脉宽为20 ns、单脉冲能量为0~22 J的Nd:YAG激光器对TiAl合金试件进行了实验研究。采用显微硬度计、表面粗糙度仪和扫描电镜分别测量了激光冲击强化前后的表面显微硬度、粗糙度和表面微观形貌,利用X射线应力分析仪测量了激光冲击强化表面残余应力和晶面极性,并分析了其高温稳定性。实验结果表明:当单脉冲能量增加到9 J时,表面显微硬度增加了33.4%,粗糙度由0.042 μm增大到了0.285 μm,表面残余压应力由20 MPa增加到了297 MPa,表面微观形貌出现了凸凹不平,局部纹理和层状微结构。将9 J激光冲击强化后的试件在650 ℃下保温4 h后,残余压应力值从297 MPa降到230 MPa,显微硬度值从377 HV_(0.2)降到345 HV_(0.2),(002)晶面取向有向中心移回的趋势。得到的数据显示,激光冲击强化能够极大地改善TiAl合金的组织和性能,且具有一定的高温稳定性。
其他语种文摘 To study the effect of laser peening on microstructures and properties of TiAl alloy, TiAl alloy samples were treated by a Nd:YAG laser system with a wavelength of 1 064 nm, a pulse-width of 20 ns, and a pulse-energy of range 0-22 J. The surface micro-hardness, roughness, and microstructural characteristics of the samples before and after laser peening were tested with a micro-hardness tester, a roughness tester and a Scanning Electron Microscope (SEM). The residual stress and pole figures of TiAl alloy were tested with X-ray Diffraction (XRD) and their high-temperature stabilities were analyzed. The experimental results show that the surface micro-hardness increases up to 33.4%, the roughness increases from 0.042 μm to 0.285 μm, the compress residual stress increases from 20 MPa to 297 MPa with the pulse energy up to 9 J, and the local textures and typical lamellar microstructures are generated. When the samples are heated for 4 h at 650 ℃, the residual stress value and micro hardness values have droped from 297 MPa to 230 MPa, and 377 HV_(0.2) to 345HV_(0.2) respectively, and the (002) poles shift back to the center slightly. It concludes that the laser peening improves microstructures and properties of TiAl alloy significantly.
来源 光学精密工程 ,2014,22(7):1766-1773 【核心库】
DOI 10.3788/ope.20142207.1766
关键词 激光冲击强化 ; 钛铝合金 ; 高温稳定性 ; 组织性能
地址

1. 中国科学院沈阳自动化研究所, 辽宁, 沈阳, 110016  

2. 中国科学院金属研究所, 辽宁, 沈阳, 110016

语种 中文
文献类型 研究性论文
ISSN 1004-924X
学科 金属学与金属工艺
基金 国家863计划
文献收藏号 CSCD:5193394

参考文献 共 13 共1页

1.  周建忠. 微尺度激光喷丸强化TiN涂层的表面性能. 光学精密工程,2011,19(11):2679-2684 被引 9    
2.  陶春虎. 航空用钛合金的失效及其预防,2002:5-10 被引 4    
3.  乔红超. 纳秒脉宽Nd:YAG激光冲击强化激光器的研制及分析. 中国激光,2013,40(8):08020011-08020017 被引 1    
4.  冯德军. 基于石墨烯可饱和吸收体的掺铒光纤环形腔脉冲激光器. 光学精密工程,2013,21(5):1097-1101 被引 10    
5.  王加贤. 纳米半导体复合薄膜的非线性光学性质及其在激光器中的应用. 光学精密工程,2013,21(1):20-25 被引 2    
6.  张晓伟. 激光原位合成TiN/Ti_3Al基复合涂层. 金属学报,2011,47(8):1086-1093 被引 31    
7.  Liu X D. Healing fatigue damage by laser shock peening for copper film. International Journal of Fatigue,2013,54:127-132 被引 4    
8.  Vasu A. Effect of curved geometry on residual stress in laser peening. Surface and Coating Technology,2013,218(1):71-79 被引 12    
9.  静永娟. 喷丸处理对TiAl合金拉伸性能的影响. 稀有金属,2009,33(5):750-753 被引 8    
10.  Chai L H. Effect of spark plasma sintering temperature on microstructure and mechanical properties of melt-spun TiAl alloys. Trans.Nonferrous Met.Soc.China,2012,22(3):528-533 被引 3    
11.  Appel F. Role of vacancies in work hardening and fatigue of TiAl alloys. Inter.Jour.Plasticity,2013,42:83-533 被引 5    
12.  陈国琳. 钛合金的发展现状及应用前景. 舰船科学技术,2009,42(12):110-113 被引 9    
13.  Liu K K. The effects of laser peening and shot peening on fretting fatigue in Ti-6Al-4V coupons. Tropology International,2009,42:1250-1262 被引 5    
引证文献 23

1 付喜宏 应用于金属焊接的光纤耦合输出2kW半导体激光光源 激光杂志,2014,35(12):68-71
被引 0 次

2 赵振兴 长期热暴露对不同表面状态的Ti-44Al-5Nb-1W-1B合金疲劳性能的影响 中国有色金属学报,2015,25(6):1458-1464
被引 6

显示所有23篇文献

论文科学数据集
PlumX Metrics
相关文献

 作者相关
 关键词相关
 参考文献相关

版权所有 ©2008 中国科学院文献情报中心 制作维护:中国科学院文献情报中心
地址:北京中关村北四环西路33号 邮政编码:100190 联系电话:(010)82627496 E-mail:cscd@mail.las.ac.cn 京ICP备05002861号-4 | 京公网安备11010802043238号