帮助 关于我们

返回检索结果

基于团簇模型的高强度马氏体沉淀硬化不锈钢成分设计
COMPOSITION DESIGN OF HIGH-STRENGTH MARTENSITIC PRECIPITATION HARDENING STAINLESS STEELS BASED ON A CLUSTER MODEL

查看参考文献26篇

王清 1   查钱锋 1   刘恩雪 1   董闯 1   王学军 2   谭朝鑫 2   冀春俊 3  
文摘 利用"团簇加连接原子"结构模型研究了马氏体沉淀硬化不锈钢的成分特征,结果表明,此类钢的基础三元Fe-Ni-Cr高温奥氏体下限成分对应团簇成分式[NiFe_(12)]Cr_3,其中NiFe_(12)为fcc结构,Ni为中心原子,其与12个Fe原子配位构成立方八面体团簇,Cr为连接原子.以[NiFe_(12)]Cr_3为基础成分式,根据团簇式自洽放大和相似组元替代原则,添加C,Mo,Nb和Cu形成多元新合金,采用铜模吸铸快冷技术制备合金,并在1323 K保温2 h进行固溶处理后水淬,然后再在753 K保温4 h进行时效处理.结果表明,固溶和时效后的系列合金的组织和性能随合金化组元的种类及含量发生变化,其中{[(Ni_(13)Cu_3)Fe_(192)](Cr_(45)Mo_(2.5)Nb_(0.5))}C_1合金在时效处理后具有较高的硬度和拉伸强度,其硬度为397 HV,屈服强度为971 MPa,抗拉强度为1093 MPa,该成分合金在3.5%NaCl(质量分数)中性溶液中具有优良的耐蚀性能.
其他语种文摘 The present work investigates composition characteristics of martensitic precipitation hardening stainless steels using a cluster-plus-glue-atom model.In this kind of steels based on the basic ternary Fe-Ni-Cr,the lowest solubility limit of high-temperature austenite corresponds to the cluster formula[NiFe_(12)]Cr_3,where NiFe_(12) is a cuboctahedron centered by Ni and surrounded by 12 Fe atoms in fee structure and Cr serves as glue atoms.New multi-component alloys were designed by adding C,Mo,Nb and Cu into the basic[NiFe_(12)]Cr_3 with self-magnification of cluster formula and similar element substitution.These alloys were prepared by copper mould suction casting method,then solid-solution treated at 1323 K for 2 h followed by water-quenching,and finally aged 753 K for 4 h.The experimental results show that the microstructures and properties of the serial solid-solution treated and aged alloys vary with alloying elements and their contents.Among them, the {[(Ni_(13)Cu_3)Fe_(192)](Cr_(45)Mo_(2.5)Nb_(0.5))}C_1 alloy has higher microhardness and tensile strengths,the hardness is 397 HV,yield strength is 971 MPa and ultra strength is 1093 MPa after aging treatment. {[(Ni_(13)Cu_3)Fe_(192)](Cr_(45)Mo_(2.5)Nb_(0.5))}C_1 exhibits good corrosion-resistance in 3.5%NaCl solution.
来源 金属学报 ,2012,48(10):1201-1206 【核心库】
DOI 10.3724/sp.j.1037.2012.00053
关键词 马氏体沉淀硬化不锈钢 ; “团簇加连接原子”结构模型 ; 合金化 ; 成分设计 ; 高强度
地址

1. 大连理工大学, 三束材料改性教育部重点实验室, 大连, 116024  

2. 沈阳鼓风机集团股份有限公司, 沈阳, 110869  

3. 大连理工大学能源与动力学院, 大连, 116024

语种 中文
ISSN 0412-1961
学科 金属学与金属工艺
基金 国家自然科学基金项目 ;  辽宁省博士后启动基金项目资助
文献收藏号 CSCD:4656636

参考文献 共 26 共2页

1.  赵先存. 高强度超高强度不锈钢,2008:244 被引 1    
2.  Floreen S. Met Rev,1968,13:115 被引 1    
3.  Decker R F. Proc Conf on Maraging Steels- Recent Developments and Applications,1988:1 被引 1    
4.  Garrison W M. JOM,1990,42:20 被引 21    
5.  周倩青. 高强高韧FV520B马氏体钢的时效工艺优化. 金属学报,2009,45:1249 被引 9    
6.  乔桂英. 特殊钢,1998,19:18 被引 7    
7.  Hsiao C N. Mater Chem Phys,2002,74:134 被引 28    
8.  Wang J. Nucl Eng Des,2006,236:2531 被引 10    
9.  Sen D. Mater Sci Eng. A,2005,397:370 被引 4    
10.  Schaeffler A L. Met Prog,1949,56:680 被引 9    
11.  Delong W T. Weld J,1956,35:s521 被引 1    
12.  Olson G B. Science,1997,277:1237 被引 29    
13.  Xu W. Acta Mater,2010,58:4067 被引 15    
14.  Dong C. J Phys. D,2007,40:273 被引 30    
15.  Wang Q. Mater Sci Eng. A,2007,18:449 被引 5    
16.  Zhang J. J Mater Res,2010,25:328 被引 17    
17.  马仁涛. 低弹bcc结构Ti-Mo-Nb-Zr固溶体合金的 "团簇+连接原子''模型及其成分设计. 金属学报,2010,46:1034 被引 12    
18.  Li B Z. Metall Mater Trans. A,2012,43:544 被引 4    
19.  Takeuchi A. Mater Trans JIM,2005,46:2817 被引 473    
20.  Raynor G V. Phase Equilibria in Iron Ternary Alloys,1988:316 被引 1    
引证文献 14

1 王清 多组元合金成分设计方法 大连理工大学学报,2013,53(6):831-837
被引 6

2 靳淑静 固溶体近程有序结构与合金设计 材料导报,2014,28(2A):114-117,123
被引 0 次

显示所有14篇文献

论文科学数据集
PlumX Metrics
相关文献

 作者相关
 关键词相关
 参考文献相关

版权所有 ©2008 中国科学院文献情报中心 制作维护:中国科学院文献情报中心
地址:北京中关村北四环西路33号 邮政编码:100190 联系电话:(010)82627496 E-mail:cscd@mail.las.ac.cn 京ICP备05002861号-4 | 京公网安备11010802043238号