TC4-DT电子束焊接头显微组织及疲劳裂纹扩展行为
Microstructure and fatigue crack growth behavior of electron beam welded joints for TC4-DT titanium alloy
查看参考文献6篇
|
文摘
|
在光学显微镜下对TC4-DT钛合金电子束焊接头显微组织进行了分析,讨论了接头不同位置显微组织特征.比较了疲劳裂纹始于焊接接头不同位置时的宏观裂纹扩展路径及裂纹扩展速率,依据焊接接头显微组织特点讨论了显微组织对疲劳裂纹扩展行为的影响.结果表明,电子束焊接头沿熔深方向显微组织存在一定的差异;文中条件下,与母材区相比焊缝熔合区及热影响区具有较高的疲劳裂纹扩展抗力,导致裂纹扩展路径逐步偏向母材区,最后讨论了裂纹扩展路径的偏折对裂纹扩展速率的影响. |
|
其他语种文摘
|
The microstructure of electron beam welded joints of TC4-DT titanium alloy was analyzed by optical microscope,and the microstructure characteristics of different position in the joint were also analyzed.The crack propagation path and its growth rate were investigated on the joint samples,which the initial crack appeared at different location of the welded joints.Based on the microstructure characteristics of the welded joints,the influences of the weld microstructure on fatigue crack growth behavior were discussed.The results show that there are differences in the microstructure for electron beam welded joint along penetration depth.The fatigue crack propagation resistances of the weld fusion zone and heat affected zone were higher than that of the base metal,and the crack propagation path of the joints gradually tended to base metal zone.The influence of the crack propagation path offsets on crack growth rate was finally discussed in the paper. |
|
来源
|
焊接学报
,2012,33(9):109-112 【核心库】
|
|
关键词
|
TC4-DT
;
电子束焊
;
接头显微组织
;
疲劳裂纹扩展
|
|
地址
|
1.
北京工业大学机械工程与应用电子技术学院, 高能束流加工技术国防重点实验室, 北京, 100124
2.
中国科学院金属研究所, 沈阳, 110016
3.
中航工业北京航空制造工程研究所, 高能束流加工技术国防重点实验室, 北京, 100024
|
|
语种
|
中文 |
|
ISSN
|
0253-360X |
|
学科
|
金属学与金属工艺 |
|
文献收藏号
|
CSCD:4650238
|
参考文献 共
6
共1页
|
|
1.
Suresh D M. A comparative evaluation of friction and electron beam welds of near-a titanium alloy.
Materials and Design,2010,31(4):2245-2252
|
被引
10
次
|
|
|
|
|
2.
Prasad Raoa K. Fracture toughness of electron beam welded Ti6Al4V.
Journal of Materials Processing Technology,2008,199(1 /3):185-192
|
被引
7
次
|
|
|
|
|
3.
曹春晓. 选材判据的变化与高损伤容限钛合金的发展.
金属学报,2002,38(s):4-11
|
被引
66
次
|
|
|
|
|
4.
Lutjering G. Influence of processing on microstructure and mechanical properties of (α + β) titanium alloys.
Materials Science and Engineering A,1998,243(1 /2):32-45
|
被引
125
次
|
|
|
|
|
5.
Filip R. The effect of microstructure on the mechanical properties of two-phase titanium alloys.
Journal of Materials Processing Technology,2003,133(1 /2):84-89
|
被引
68
次
|
|
|
|
|
6.
马英杰. 钛合金β晶粒生长规律及晶粒尺寸对损伤容限性能的影响.
稀有金属材料与工程,2009,38(6):976-981
|
被引
15
次
|
|
|
|
|
了解气象卫星更多信息，请访问