|
|
Numerical Simulation and Experimental Investigation of Springback in U-Channel Forming of Tailor Rolled Blank
查看参考文献9篇
|
文摘
|
In order to grasp the springback rule of TRB (tailor rolled blank) parts after forming, the springback behavior of TRB was investigated by integrating such three means as theoretical research, numerical simulation and stamping experiments.Fundamental theories of springback were analyzed.The stamping and springback processes of annealed 1.2 / 2.0mm TRB, 1.2mm and 2.0mm plates for U-channel were simulated, and the simulation results were compared with the experiments.The results indicate that the springback of TRB falls in between those of the 1.2mm and 2.0mm plates.It is desirable for the TRB U-channel to have die clearance of 1.1times maximum blank thickness and friction coefficient of about 0.12, and longer thickness transition zone is preferable.The simulation data demonstrate reasonably good agreement with the experiments. |
|
来源
|
Journal of Iron and Steel Research
, International,2012,19(9):8-12 【核心库】
|
|
DOI
|
10.1016/s1006-706x(13)60002-3
|
|
关键词
|
tailor rolled blank
;
U-channel
;
springback
;
annealing
|
|
地址
|
1.
Faculty of Vehicle Engineering and Mechanics, Dalian University of Technology, State Key Laboratory of Structural Analysis for Industrial Equipment, Liaoning, Dalian, 116024
2.
Research Institute of Science and Technology, Northeastern University, Liaoning, Shenyang, 110819
|
|
语种
|
英文 |
|
ISSN
|
1006-706X |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家973计划
;
Fundamental Research Funds for Central Universities of China
;
国家自然科学基金
|
|
文献收藏号
|
CSCD:4632632
|
参考文献 共
9
共1页
|
|
1.
Ryabkov N. Production of Blanks With Thickness Transitions in Longitudinal and Lateral Direction Through 3D-Strip Profile Rolling.
International Journal of Material Forming,2008(S1):391
|
被引
10
次
|
|
|
|
|
2.
Meyer A. Increasing of the Drawing Depth Using Tailor Rolled Blanks—Numerical and Experimental Analysis.
International Journal of Machine Tools and Manufacture,2008,48(5):522
|
被引
42
次
|
|
|
|
|
3.
Chou I N. Finite Element Analysis and Optimization on Springback Reduction.
International Journal of Machine Tools and Manufacture,1999,39(3):517
|
被引
6
次
|
|
|
|
|
4.
Xie Hui. Analysis of Factors Infecting Sheet′s Springback Based on CAE.
Journal of Hunan University: Natural Sciences (in Chinese),2003(5):29
|
被引
1
次
|
|
|
|
|
5.
Kim D. Study of Residual Stresses in Tailor Rolled Blanked Al5J322T4Sheets.
Rare Metals,2006,25:111
|
被引
9
次
|
|
|
|
|
6.
Liu Xianghua. Prospects for Variable Gauge Rolling: Technology, Theory and Application.
Journal of Iron and Steel Research,International,2011,18(1):1
|
被引
33
次
|
|
|
|
|
7.
Du Ping. Multiple-Point Dynamic Setting for Variable Cross-Section Rolling Process.
Journal of Iron and Steel Research (in Chinese),2009,21(11):27
|
被引
5
次
|
|
|
|
|
8.
Jiang Yinfang. Research on Resilience Characteristics and Control of Continuous Variable Cross Section Beams.
Machine Design (in Chinese),2010,27(1):10
|
被引
1
次
|
|
|
|
|
9.
Zhao Guowei. Numerical Simulation and Infecting Factors of Springback in Sheet Metal Forming.
China Metal Forming Equipment and Manufacturing Technology (in Chinese),2005(3):55
|
被引
1
次
|
|
|
|
|
|
了解气象卫星更多信息，请访问