帮助 关于我们

返回检索结果

有限变形下的后继屈服面演化规律研究
A STUDY ON THE EVOLUTION OF SUBSEQUENT YIELD SURFACES WITH FINITE DEFORMATION

查看参考文献27篇

文摘 有限变形下的后继屈服面会出现膨胀或收缩,移动和畸变等变形特征。基于塑性变形的滑移机制,建立了适用于有限变形条件下的多晶塑性本构模型。提出了一种混合硬化假设,可以一致描述后继屈服面演化中的等向、运动和畸变硬化以及正或负交叉效应、包氏效应等。预测了2种加工硬化铝合金(Al6061-T6511和annealed1100Al)分别在单轴拉伸和纯扭转下的后继屈服面演化过程,与已有实验结果符合一致。
其他语种文摘 The subsequent yield surfaces after a finite deformation show expansion or contraction,translation and distortion.Based on the slip mechanism,a plastic constitutive model for polycrystalline metals with a finite deformation is proposed.A mixed hardening model is developed in the present paper to describe the isotropic hardening,kinematic hardening,distortional hardening,positive or negative cross-effect and Bauschinger effect characterized by the evolution of subsequent yield surfaces.Numerical simulations of the evolution of yield surfaces are performed under tension and pure torsion at various levels of straining for two kinds of work hardening aluminum alloys(Al6061-T6511 and annealed 1100Al).The results show that the agreement between the predictions and experiments is quite satisfactory.
来源 工程力学 ,2011,28(11):23-30 【核心库】
关键词 有限变形 ; 多晶塑性本构模型 ; 后继屈服面演化 ; 混合硬化 ; 低/高加工硬化铝合金
地址

中国科学院力学研究所, 非线性力学国家重点实验室, 北京, 100190

语种 中文
文献类型 研究性论文
ISSN 1000-4750
学科 力学
基金 国家自然科学基金项目
文献收藏号 CSCD:4365892

参考文献 共 27 共2页

1.  Khan A S. Evolution of subsequent yield surfaces and elastic constants with finite plastic deformation. Part-I: A very low work hardening aluminum alloy (A16061-T6511). International Journal of Plasticity,2009,25(9):1611-1625 被引 13    
2.  Khan A S. Evolution of subsequent yield surfaces and elastic constants with finite plastic deformation, part-II: A very high work hardening aluminum alloy (annealed 1100 A1). International Journal of Plasticity,2010,26(10):1421-1431 被引 8    
3.  Khan A S. Evolution of subsequent yield surfaces and elastic constants with finite plastic deformation, part-III: Yield surface in tension-tension stress space (A1 6061-T 6511 & annealed 1100 AI). International Journal of Plasticity,2010,26(10):1432-1441 被引 7    
4.  张泽华. 塑性本构关系的实验研究. 塑性力学进展,1988:144-178 被引 5    
5.  Khan A S. An experimental study on subsequent yield surface after finite shear prestraining. International Journal of Plasticity,1993,9(8):889-905 被引 8    
6.  Stout M G. Multiaxial yield behavior of 1100 aluminum following various magnitudes of prestrain. International Journal of Plasticity,1985,1(2):163-174 被引 2    
7.  Tozawa Y. Plastic deformation behavior under conditions of combined stress. Mechanics of Sheet Metal Forming,1978 被引 1    
8.  Williams J. Effect of tensile prestrain on the yield locus of 1100-f aluminium. The Journal of Strain Analysis for Engineering Design,1970,5(2):128-139 被引 1    
9.  Williams J. Effect of torsional prestrain on the yield locus of 1100-F aluminium. The Journal of Strain Analysis for Engineering Design,1971,6(4):263-272 被引 1    
10.  Aretz H. A simple isotropic-distortional hardening model and its application in elastic-plastic analysis of localized necking in orthotropic sheet metals. International Journal of Plasticity,2008,24:1457-1480 被引 6    
11.  Rousselier G. A novel approach for anisotropic hardening modeling. Part I: Theory and its application to finite element analysis of deep drawing. International Journal of Plasticity,2009,25:2383-2409 被引 2    
12.  Vincent L. A general cyclic plasticity model taking into account yield surface distortion for multiaxial ratchetting. International Journal of Plasticity,2004,20(10):1817-1850 被引 3    
13.  Chiang D Y. A study on subsequent yield surface based on the distributed-element model. International Journal of Plasticity,2002,18(1):51-70 被引 4    
14.  Yeh W C. An endochronic model of yield surface accounting for deformation induced anisotropy. International Journal of Plasticity,2006,22(1):16-38 被引 3    
15.  Francois M. A plasticity model with yield surface distortion for non proportional loading. International Journal of Plasticity,2001,17(5):703-717 被引 7    
16.  Mollica F. A general framework for generating convex yield surfaces for anisotropic metals. Acta Mechanica,2002,154(1/2/3/4):61-84 被引 2    
17.  Wu H C. On finite plastic deformation of anisotropic metallic materials. International Journal of Plasticity,2003,19(1):91-119 被引 1    
18.  Zattarin P. Numerical study of the influence of microstructure on subsequent yield surfaces of polyerystalline materials. International Journal of Mechanical Sciences,2004,46(9):1377-1398 被引 3    
19.  Suprun A N. A constitutive model with three plastic constants: The description of anisotropic workhardening. International Journal of Plasticity,2006,22(7):1217-1233 被引 3    
20.  付强. 一种基于物理机制的后继屈服面演化模型. 力学学报,2010,42(5):880-888 被引 7    
引证文献 2

1 陈岑 双轴拉伸应力下后继屈服面的演化研究 航空学报,2012,33(12):2230-2239
被引 2

2 陈岑 有限变形下材料的弹塑性损伤行为及结构响应分析 工程力学,2014,31(11):9-16
被引 1

显示所有2篇文献

论文科学数据集
PlumX Metrics
相关文献

 作者相关
 关键词相关
 参考文献相关

版权所有 ©2008 中国科学院文献情报中心 制作维护:中国科学院文献情报中心
地址:北京中关村北四环西路33号 邮政编码:100190 联系电话:(010)82627496 E-mail:cscd@mail.las.ac.cn 京ICP备05002861号-4 | 京公网安备11010802043238号