Ni-Al基自润滑复合材料的制备及其摩擦学性能
Preparation and Tribological Properties of Ni-Al-based Self-lubricating Composites
查看参考文献14篇
|
文摘
|
本文采用粉末冶金的方法制备了Ni-Al基自润滑复合材料并研究了烧结温度对复合材料的机械及摩擦性能的影响,同时讨论了复合材料在不同试验条件下的摩擦磨损性能.结果表明,烧结温度越高,复合材料的致密性和显微硬度越高,摩擦性能也越稳定.在摩擦磨损试验过程中,试验载荷和频率对复合材料的摩擦性能也有一定影响,在其它参数不变的情况下,载荷越大,自润滑材料的摩擦系数越小;频率越大,材料的摩擦系数越大.加入5wt.%鳞片状石墨后, Ni-Al复合材料的硬度明显降低,摩擦系数在室温和600℃有不同程度的降低 |
|
其他语种文摘
|
Ni-Al based self-lubricating composites were prepared by powder metallurgy method. The influence of sintering temperature on mechanical and tribological properties of composites was investigated and the tribological properties of composites in different testing conditions were discussed as well. The results show that the higher the sintering temperature, the higher the compactness and micro-hardness of composites, and the tribological properties of composites were more stable. The effects of applied load and reciprocating frequency on tribological properties of composites are as following: the greater the load, the lower the friction coefficient;the higher the frequency, the higher the friction coefficient of composites. Furthermore, the micro-hardness of Ni-Al-based self-lubricating composites with 5 wt.% flake graphite is obviously decreased comparing with that of the composite without flake graphite, and the friction coefficients of composites with graphite were likewise lower than that of the composite without graphite at both ambient temperature and 600℃ |
|
来源
|
材料科学与工程学报
,2011,29(1):80-85,142 【核心库】
|
|
关键词
|
粉末冶金
;
Ni-Al基复合材料
;
摩擦性能
|
|
地址
|
1.
兰州理工大学, 甘肃省有色金属新材料省部共建国家重点实验室, 甘肃, 兰州, 730050
2.
兰州理工大学, 甘肃省有色金属新材料省部共建国家重点实验室;;固体润滑国家重点实验室, 甘肃, 兰州, 730050
3.
中国科学院兰州化学物理研究所, 固体润滑国家重点实验室, 甘肃, 兰州, 730000
|
|
语种
|
中文 |
|
ISSN
|
1673-2812 |
|
学科
|
机械、仪表工业 |
|
基金
|
中国科学院“百人计划”项目
;
国家自然科学基金资助项目
|
|
文献收藏号
|
CSCD:4142817
|
参考文献 共
14
共1页
|
|
1.
李玉峰. 高温固体润滑材料研究的发展现状.
热处理技术与装备,2007,28(6):2-9
|
被引
16
次
|
|
|
|
|
2.
刘如铁. 镍基高温自润滑材料.
湖南有色金属,1998,14(5):25-29
|
被引
7
次
|
|
|
|
|
3.
朱定一. 镍-石墨高温自润滑材料的熔炼制备及其组织性能.
中国有色金属学报,2004,14(5):707-712
|
被引
18
次
|
|
|
|
|
4.
Donnet C. Solid lubricant coatings: recent developments and future trends.
Tribology Letters,2004,17(3):389-397
|
被引
36
次
|
|
|
|
|
5.
Li J L. Tribological behavior of graphitecontaining nickel-based composite as function of temperature load and counterface.
Wear,2009,266:360-367
|
被引
9
次
|
|
|
|
|
6.
Bryant P J. A study of mechanisms of graphite friction and wear.
Wear,1964,7(3):118-119
|
被引
6
次
|
|
|
|
|
7.
卢铃. 金属基／石墨固体自润滑材料的研究进展.
材料导报,2007,21(2):38-42
|
被引
6
次
|
|
|
|
|
8.
丁春华. 粉末冶金制备NiCr基高温自润滑合金PM304涂层.
金属学报,2006,42(11):1216-1226
|
被引
2
次
|
|
|
|
|
9.
朱定一. Ni-石墨固体自润滑材料的塑性变形.
中国有色金属学报,2006,16(5):762-767
|
被引
5
次
|
|
|
|
|
10.
薛茂权. 高温固体润滑材料的研究现状.
兵器材料科学与工程,2003,26(6):59-62
|
被引
2
次
|
|
|
|
|
11.
Lu J J. Mechanical and tribological properties of Ni-based alloy/CeF3/graphite high temperature self-lubricating composites.
Wear,2001,249:1070-1076
|
被引
11
次
|
|
|
|
|
12.
薛群基. 高温固体润滑研究的现状及发展趋势.
摩擦学学报,1999,19(1):91-96
|
被引
73
次
|
|
|
|
|
13.
陈锐. 固体润滑材料-石墨的应用.
炭素,2000,4:23-25
|
被引
4
次
|
|
|
|
|
14.
潘蛟亮. Ni包石墨对镍基涂层摩擦学性能的影响.
热加工工艺,2007,36(19):57-59
|
被引
3
次
|
|
|
|
|
了解气象卫星更多信息，请访问