转速对高压扭转Cu试样的组织与性能的影响
Effect of revolution speed on microstructure and microhardness of Cu spencimens subjected to high-pressure torsion
查看参考文献19篇
|
文摘
|
通过高压扭转(HPT)技术在不同转速条件下实现了Cu试样的晶粒细化.利用光学显微镜(OM),透射电镜(TEM)及显微硬度计观察并测试了组织的结构与性能,并基于有限元计算了变形诱导试样的温升,研究了转速对Cu试样的组织细化与性能的影响.结果表明:转速由1/3r.min-1增大至1r.min-1,经1圈扭转变形,试样温度由40.8℃升高到54.1℃,变形组织均为100~600nm的高位错密度位错胞/亚晶组织,显微硬度由初始态的52HV0.05增大至140HV0.05;经16圈扭转变形,试样温度由50.4℃升高到97.4℃,组织细化到200nm.慢速扭转变形试样晶内位错密度高,微观组织处于严重变形状态;而快速扭转试样晶内衬度均匀,位错较少,微观组织经历明显的动态回复,显微硬度较慢速扭转变形试样低6% |
|
其他语种文摘
|
Cu specimens were deformed by high-pressure torsion(HPT)at different revolution speeds,to investigate the effect of revolution speed on its microstructure and mechanical properties by means of OM,TEM and microhardness testing. It was found that heavily deformed microstructure with average grain size in 200 nm formed in the sample after HPT deforming to large strains at a revolution speed of 1/3 r.min-1. Increasing revolution speed up to 1 r.min-1, some dislocation-free fine grains appears, leading to a 6 percent of decrease in average hardness as compared to the lower revolution speed counterparts. One turn of HPT deformation induces dislocation-cells/subgrains with size in 100-600 nm formed and an increase in hardness from 52 to 140 HV0.05.The evolution of the microstructure and mechanical properties with revolution speed was interpreted by using a thermal analysis simulation based on heat generation induced by the extensive HPT deformation |
|
来源
|
材料热处理学报
,2010,31(11):109-115 【核心库】
|
|
关键词
|
Cu
;
高压扭转
;
微观结构
;
显微硬度
;
扭转速度
|
|
地址
|
1.
温州大学建筑与土木工程学院, 非线性力学国家重点实验室, 浙江, 温州, 325035
2.
中国科学院力学研究所, 非线性力学国家重点实验室, 北京, 100190
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1009-6264 |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家自然科学基金项目
|
|
文献收藏号
|
CSCD:4066695
|
参考文献 共
19
共1页
|
|
1.
Valiev R Z. Bulk nanostructured materials from severe plastic deformation.
Progress in Materials Science,2000,45(2):103-189
|
被引
499
次
|
|
|
|
|
2.
WANG J T. Lamellae deformation and structural evolution in an Al-33%Cu eutectic alloy during equal-channel angular pressing.
Journal of Materials Science,2002,37(12):5223-5227
|
被引
3
次
|
|
|
|
|
3.
HUANG C X. Deformation twinning in polycrystalline copper at room temperature and low strain rate.
Acta Materialia,2006,54(3):655-665
|
被引
27
次
|
|
|
|
|
4.
WU X L. Microstructural evolution and formation of nanocrystalline intermetallic compound during surface mechanical attrition treatment of cobalt.
Acta Materialia,2007,55(17):5768-5779
|
被引
17
次
|
|
|
|
|
5.
Hughes D A. High angle boundaries formed by grain subdivision mechanisms.
Acta Materialia,1997,45(9):3871-3886
|
被引
36
次
|
|
|
|
|
6.
ZHAO Y H. Influence of stacking fault energy on nanostructure formation under high pressure torsion.
Materials Science and Engineering A,2005,410/411(25):188-193
|
被引
4
次
|
|
|
|
|
7.
Zhilyaev A P. Microhardness and microstructural evolution in pure nickel during high-pressure torsion.
Scripta Materialia,2001,44(12):2753-2758
|
被引
13
次
|
|
|
|
|
8.
Zehetbauer M J. The role of hydrostatic pressure in severe plastic deformation.
Advanced Engineering Materials,2003,5(5):330-337
|
被引
3
次
|
|
|
|
|
9.
Hebesberger T. Structure of Cu deformed by high pressure torsion.
Acta Materialia,2005,53(2):393-402
|
被引
15
次
|
|
|
|
|
10.
Horita Z J. Microstructures and microhardness of an aluminum alloy and pure copper after processing by high-pressure torsion.
Materials Science Engineering A,2005,410/411(25):422-425
|
被引
1
次
|
|
|
|
|
11.
Wetscher F. Cyclic high-pressure torsion of nickel and Armco iron.
Philisophical Magazine,2006,86(36):5867-5883
|
被引
1
次
|
|
|
|
|
12.
Todaka Y. Effect of strain path in high-pressure torsion process on hardening in commercial purity titanium.
Materials Transactions,2008,49(1):47-53
|
被引
1
次
|
|
|
|
|
13.
谢子令. 高压扭转铜试样的微观组织与压缩性能.
金属学报,2008,44(7):803-809
|
被引
13
次
|
|
|
|
|
14.
Humphreys F J.
Recrystallization and Related Annealing Phenomena,2004
|
被引
55
次
|
|
|
|
|
15.
Mishra A. Microstructural evolution in copper subjected to severe plastic deformation: Experiments and analysis.
Acta Materialia,2007,55(1):13-28
|
被引
30
次
|
|
|
|
|
16.
Wetscher F.
Effect of large shear deformation on rail steels and pure metals. Doctoral Thesis,2006:26-27
|
被引
1
次
|
|
|
|
|
17.
LU K. Surface nanocrystallization(SNC)of metallic materials-Presentation of the concept behind a new approach.
Journal of Materials Science and Technology,1999,15(3):193-197
|
被引
205
次
|
|
|
|
|
18.
ZHANG H W. Formation of nanostructured surface layer on AISI 304 stainless steel by means of surface mechanical attrition treatment.
Acta Materialia,2003,51(7):1871-1881
|
被引
88
次
|
|
|
|
|
19.
WANG K. Plastic strain-induced grain refinement at the nanometer scale in copper.
Acta Materialia,2006,54(19):5281-5291
|
被引
67
次
|
|
|
|
|
了解气象卫星更多信息，请访问