铝合金/镁合金搅拌摩擦焊接界面处Mg/A1反应及接头力学性能
Mg/Al REACTION AND MECHANICAL PROPERTIES OF A1 ALLOY/Mg ALLOY FRICTION STIR WELDING JOINTS
查看参考文献21篇
|
文摘
|
采用搅拌针16.中(M4A4)、向镁合金侧偏置 2 mm (M6A2)和向铝合金侧偏置 2 mm (A6M2) 3种焊接方式, 研究了6 mm厚6061-T651铝合金和AZ31镁合金轧制板材的搅拌摩擦焊接.SEM及XRD分析表明, 3种焊接方式均在焊接界面处发现Mg_(17)A1_(12)相的生成和由于共晶相熔化和随后冷却所形成的孔洞.在M4A4和M6A2样品中, 少量的Al搅入到镁合金侧形成金属间化合物Mg_(17)A1_(12), 而在A6M2样品中, 少量的Mg搅入到铝合金中也形成金属间化合物Mg_(17)A1_(12),在 Mg_(17)A1_(12)与基体的界面处存在微小孔洞.由于焊核区仅有少量的Mg_(17)A1_(12)生成, 其硬度变化并不显著.焊接界面处生成的金属间化合物及孔洞显著降低接头的拉伸性能 |
|
其他语种文摘
|
Mg alloys are increasingly used in aerospace, aircraft and automotives structures due to the low density and good damping properties, especially, the welding of Mg alloy to Al alloys is of practical importance for widening the application of Mg alloys. Although friction stir welding (FSW) has been used to join Mg and A1 alloys, defect free joints are achieved only in the thin plate (less than 4 mm). In this paper, three ways of FSW of 6 mm thick 6061-T651 Al alloy and AZ31 Mg alloy plates, offsetting the pin to the seam between the two plates (M4A4), to the Mg alloy side 2 mm (M6A2) and to the Al alloy side 2 mm (A6M2), were studied. The aim is to examine the effects of the relative position between tool and plate on the microstructure and mechanical properties of FSW Mg/Al alloys joint. SEM and XRD analyses revealed the formations of intermetallics Mg_(17)A1_(12) and voids in the interface between Mg and Al alloy plates in the three FSW samples. The voids are resulted from the melting and subsequent solidification of eutectic. In the M4A4 and M6A2 samples, some Al are stirred into the Mg alloy side during FSW, forming the Mg_(17)A1_(12), whereas in the A6M2 sample, some Mg stirred into the Al alloy side are also transformed to the Mg_(17)A1_(12). Some fine pores are observed around the Mg_(17)A1_(12). The hardness of the nugget zone exhibits a slight increase due to the formation of a small amount of Mg_(17)A1_(12). The intermetallics and pores at the jointed interface decrease the strength of the joints significantly |
|
来源
|
金属学报
,2010,46(5):589-594 【核心库】
|
|
DOI
|
10.3724/sp.j.1037.2009.00802
|
|
关键词
|
搅拌摩擦焊
;
异种材料焊接
;
6061铝合金
;
AZ31镁合金
;
显微组织
|
|
地址
|
1.
中国科学院金属研究所, 沈阳材料科学国家(联合)实验室, 沈阳, 110016
2.
中航工业黎明公司, 沈阳, 110043
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
0412-1961 |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家自然科学基金国家杰出青年科学基金
;
中国科学院“百人计划”项目
|
|
文献收藏号
|
CSCD:3934435
|
参考文献 共
21
共2页
|
|
1.
Mordike B L.
Mater Sci Eng. A,2001,302:37
|
被引
1180
次
|
|
|
|
|
2.
Hatch J E.
Aluminum Properties and Physical Metallvrgy, Metals Park,1984:1
|
被引
1
次
|
|
|
|
|
3.
Liu P.
Mater Lett,2007,61:1288
|
被引
19
次
|
|
|
|
|
4.
Liu L M.
Scr Mater,2006,55:383
|
被引
18
次
|
|
|
|
|
5.
Mishra R S.
Mater Sci Eng,2005,R50:1
|
被引
526
次
|
|
|
|
|
6.
任淑荣. 焊后热处理工艺和背部二次焊接对搅拌摩擦焊接7075-T651铝合金性能的影响.
金属学报,2007,42:225
|
被引
19
次
|
|
|
|
|
7.
谢广明.
金属学报,2008,44:655
|
被引
1
次
|
|
|
|
|
8.
Xie G M.
J Mater Sci Technol,2009,25:351
|
被引
9
次
|
|
|
|
|
9.
Khodir S A.
Mater Trans,2007,48:2501
|
被引
1
次
|
|
|
|
|
10.
Somasekharan A C.
Mater Charact,2004,52:49
|
被引
25
次
|
|
|
|
|
11.
Yan J C.
Scr Mater,2005,53:585
|
被引
10
次
|
|
|
|
|
12.
Kostka A.
Scr Mater,2009,60:953
|
被引
20
次
|
|
|
|
|
13.
Sato Y S.
Scr Mater,2004,50:1233
|
被引
45
次
|
|
|
|
|
14.
Chen Z W.
Scr Mater,2008,58:417
|
被引
10
次
|
|
|
|
|
15.
Prangnell P B.
Acta Mater,2005,53:3179
|
被引
32
次
|
|
|
|
|
16.
Fatemi-Varzaneh S M.
Mater Sci Eng. A,2008,497:438
|
被引
11
次
|
|
|
|
|
17.
王祝堂.
铝合金及其加工乎册(第3版),2005:317
|
被引
1
次
|
|
|
|
|
18.
Feng A H.
Scr Mater,2007,56:397
|
被引
21
次
|
|
|
|
|
19.
Mahoney NI W.
Metalt Mater Trans.A,1998,29:1955
|
被引
1
次
|
|
|
|
|
20.
Yang J.
Mater Sci. En., g. A,2010,527:708
|
被引
15
次
|
|
|
|
|
了解气象卫星更多信息，请访问