高强高韧FV520B马氏体钢的时效工艺优化
AGING PROCESS OPTIMIZATION FOR A HIGH STRENGTH AND TOUGHNESS OF FV520B MARTENSITIC STEEL
查看参考文献17篇
文摘
|
通过在600,630,680,700和720℃保温1 h空冷,以及在630℃短时时效后炉冷和空冷的热处理,研究了不同时效温度,时效时间以及冷却方式对沉淀硬化马氏体不锈钢FV520B的组织和力学性能的影响.结果表明,630℃短时时效后钢中即可析出一定量的逆转变奥氏体,且钢中的析出相尺寸较小并弥散分布,由此提出了一种沉淀强化马氏体不锈钢的热处理工艺优化,即FV520B钢经630℃短时时效并炉冷后,可以获得较佳的高强度和高韧性组合. |
其他语种文摘
|
Low carbon martensitic precipitation hardening stainless steels are widely utilized in many engineering applications due to their high strength with reasonable toughness, ductility and corrosion resistance. However, those properties and their combinations are not always satisfactory to their users. For further improvement of the mechanical properties of these types of steels, a fundamen-tal understanding of the detailed microstructural features with various aging conditions is necessary. Therefore, the effects of aging temperature, aging time and cooling rate on the microstructure and me-chanical properties of a martensitic precipitation hardening stainless steel FV520B were investigated by OM, SEM, TEM and XRD methods. The results show that the steel aged at 630 ℃ for a short time and then furnace cooled, in which a typical lath martensitic with the proper amounts of reverse austenite and fined dispersed precipitates was observed, has a good combination of high strength and high toughness. It could be an optimized aging process for FV520B steel. |
来源
|
金属学报
,2009,45(10):1249-1254 【核心库】
|
关键词
|
马氏体钢
;
逆转变奥氏体
;
析出相
;
时效
|
地址
|
东北大学材料与冶金学院, 辽宁, 沈阳, 110004
|
语种
|
中文 |
文献类型
|
研究性论文 |
ISSN
|
0412-1961 |
学科
|
金属学与金属工艺 |
文献收藏号
|
CSCD:3725739
|
参考文献 共
17
共1页
|
1.
Ping D H.
Material Science and Engineering A,2005,394:285
|
被引
26
次
|
|
|
|
2.
Nakagawa H.
Journal of Materials Science,2000,35:2245
|
被引
14
次
|
|
|
|
3.
Mo D F.
J Iron Steel Res (Int),2009,16(1):87
|
被引
4
次
|
|
|
|
4.
Renterghem W V.
Journal of Nuclear Materials,2007,360:128
|
被引
1
次
|
|
|
|
5.
Murayama M.
Metallurgical and Materials Transactions A,1999,30:345
|
被引
20
次
|
|
|
|
6.
刘晓禹.
一重技术,2005,106(4):27
|
被引
4
次
|
|
|
|
7.
牛靖.
铸造技术,2006,27:921
|
被引
4
次
|
|
|
|
8.
牛靖. FV520(B)钢时效组织和力学性能分析.
热加工工艺,2006,35(4):33
|
被引
10
次
|
|
|
|
9.
Li X Y.
Adv Cryogenic Eng:Trans Int Cryogenic Mater Conf-ICMC,2008:145
|
被引
1
次
|
|
|
|
10.
Tanaka M.
Trans ISIJ,1972,12:16
|
被引
2
次
|
|
|
|
11.
许荣昌.
莱钢科技,2007,129(3):14
|
被引
1
次
|
|
|
|
12.
孙全社. 添加钛、铌的超低碳钢在不同工艺过程中的析出相分析.
钢铁研究学报,2006,18(2):41
|
被引
5
次
|
|
|
|
13.
叶冰.
特钢技术,2001,9(1):47
|
被引
2
次
|
|
|
|
14.
张秀丽.
宽厚板,2002,8(2):12
|
被引
2
次
|
|
|
|
15.
叶冰.
特钢技术,2006,11(2):29
|
被引
2
次
|
|
|
|
16.
Bilmes P D.
Materials Characterization,2001,46:285
|
被引
29
次
|
|
|
|
17.
Lee D S.
Scripta Materialia,2001,45:767
|
被引
1
次
|
|
|
|
|