|
|
三维连通网状SiC陶瓷／Zr基非晶复合材料动态变形特征
Dynamic Deformation and Fracture Behavior of 3D-Net SiC/Zr-Based Amorphous Matrix Composites
查看参考文献9篇
|
文摘
|
利用分离式霍普金森压杆装置，对三维连通网状SiC陶瓷／Zr基非晶复合材料进行不同应变率下的动态压缩实验，采用扫描电子显微镜研究复合材料的动态变形特征和断口形貌．结果表明：复合材料的动态压缩强度随着打击速度的增加而增加；试样发生劈裂和剪切断裂，陶瓷相断口形貌为层片状、台阶式的解理断裂，非晶合金发生粘性流动。断口形貌复杂多样．在应变率〉10~4s~(-1)的冲击载荷下，非晶相表现为软化后的多重脊状条带．复合材料断口上大量的非晶球形液滴及非晶软化条带的发现表明，绝热温升在非晶变形与断裂过程中起重要作用． |
|
其他语种文摘
|
Dynamic deformation and fracture behavior of 3D-net SiC/Zr-based amorphous matrix composites at room temperature and various strain rates in compression was investigated by means of the split Hopkinson pressure bar （SHPB）. The phase structure and failure surfaces were identified by scanning electron microscopy （SEM）. It was found that, the dynamic compressive strength increases with increasing strain rates. The mode of failure of the composites is a mixture combining splitting and shear fracture. 3D-net SiC exhibits typical cleavage fracture, and inhomogeneous flow deformation of the amorphous alloys matrix occurs leaving complex fracture surfaces. Under higher shock loading （rate of strain〉10~4 s~(-1) ）, substantive elongated ridge-like structure （melted belts） were observed on the fracture surface of Zr-based amorphous. The observed numerous liquid droplets and melted belts on the fracture surface demonstrated that the adiabatic heating exerts a significant effect on the fracture behavior of the amorphous alloys. |
|
来源
|
北京理工大学学报
,2007,27(1):77-81 【核心库】
|
|
关键词
|
三维连通网状SiC陶瓷／Zr基非晶复合材料
;
动态压缩
;
高能冲击
;
动态变形
|
|
地址
|
1.
北京理工大学材料科学与工程学院, 北京, 100081
2.
中国科学院金属研究所, 辽宁, 沈阳, 110015
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1001-0645 |
|
学科
|
一般工业技术 |
|
基金
|
国家部委项目
|
|
文献收藏号
|
CSCD:2733007
|
参考文献 共
9
共1页
|
|
1.
Inoue A. Stabilization of metallic supercooled liquid and bulk amorphous alloys.
Acta Materialia,2000,48:279-306
|
被引
580
次
|
|
|
|
|
2.
Conner R D. Mechanical properties of tungsten and steel fiber reinforced Zr4125Ti13 75Cu12 5Ni10Be22 5 metallic glass matrix composites.
Acta Materialia,1998,46:6089-6102
|
被引
80
次
|
|
|
|
|
3.
Choi-Yim H. Synthesis and characterization of particulate reinforced Zr57Ni5Al10Cu15 4Ni12 6 bulk metallic glass composites.
Acta Materialia,1999,47:2455-2462
|
被引
35
次
|
|
|
|
|
4.
Wu X F. Effect of SiCp on the glass forming ability and thermal stability of Zr55Al10Ni5Cu30 bulk metallic glass.
Acta Metallurgica Sinica (in Chinese),2003,39:414-418
|
被引
3
次
|
|
|
|
|
5.
Clark D R. Interpenetrating phase composites.
Journal of American Ceramic Society,1992,75(4):739-759
|
被引
38
次
|
|
|
|
|
6.
Zhang Q S. Compression fracture of bulk Zr55Al10Ni5Cu30 amorphous alloy at high temperature.
Acta Metallurgica Sinica (in Chinese),2002,38(8):835-838
|
被引
1
次
|
|
|
|
|
7.
Spaepen F. A microscopic mechanism for steady state inhomogeneous flow in metallic glasses.
Acta Metall,1977,25:407-415
|
被引
209
次
|
|
|
|
|
8.
Bruck H A. The dynamic compressive behavior of Beryllium bearing bulk metallic glass.
J Mater Res,1996,11:503-511
|
被引
44
次
|
|
|
|
|
9.
Subhash G. Characterization of uniaxial compressive response of a bulk amorphous Zr412Ti13 8Cu12 5Ni10Be22 5 alloy.
Mater Sci Eng A,2002,334(1/2):33-40
|
被引
27
次
|
|
|
|
|
|
了解气象卫星更多信息，请访问