帮助 关于我们

返回检索结果

1.2m地平式望远镜伺服控制和传动系统的特性研究--伺服系统校正网络在控制系统中的作用(二)
The Research on Property of Servo-control and Drive System for 1.2m Alt-Az Telescope--The Function of Servo System Compensation Network in Control System (2)

查看参考文献4篇

文摘 根据云南天文台1.2m地平式望远镜对近地卫星激光测距要求,以及对串联校正网络在控制系统中的作用分析和实际观测的结果,详细讨论了1.2m望远镜伺服系统校正网络以及经其补偿作用后系统的控制性能.得到在两点摩擦传动时,使用超前校正网络后,望远镜的快速跟踪性能得到了大大提高,能够达到的方位最大角加速度为10°/s2, 方位最大角速度5°/s,满足跟踪近地卫星的要求.
其他语种文摘 According to the requirement of SLR (Satellite Laser Range) using 1.2 m Alt-Az telescope of Yunnan Observatory, and the analysis of function of cascade compensation network in control system and the observation results, the compensation network of servo system of 1.2 m Alt-Az telescope, and the performance of control system after its compensation are discussed in this article. When friction drive is fulfilled by two torque motors, and PD compensation network in servo control system is used, it is found that the capability of rapid tracking of the 1.2 m telescope is actually improved, and the telescope can achieve 10°/s2 of maximum azimuth angle acceleration, 5°/s of maximum azimuth angle velocity, and it can meet the demand of tracking satellites near the Earth.
来源 天文研究与技术 ,2005,2(2):130-136 【核心库】
关键词 伺服控制系统 ; 串联校正网络 ; 超前校正 ; 滞后校正
地址

中国科学院国家天文台云南天文台, 云南, 昆明, 650011

语种 中文
文献类型 研究性论文
ISSN 1672-7673
学科 天文学
文献收藏号 CSCD:1956092

参考文献 共 4 共1页

1.  李祝莲. 1.2m地平式望远镜伺服控制和传动系统的特性--单点和多点摩擦传动的力学特性(一). 天文研究与技术,2005,2(1):54-59 被引 4    
2.  谢红卫(译). 谢红卫. 现代控制系统(第8版) 被引 1    
3.  徐俊. 计算机控制技术[M]. 计算机控制技术 被引 1    
4.  戴蓓倩. 线性电子线路[M]. 线性电子线路 被引 1    
引证文献 1

1 邓林华 1m红外太阳望远镜光电导行系统的反馈控制分析 天文研究与技术,2009,6(4):310-318
被引 4

显示所有1篇文献

论文科学数据集
PlumX Metrics
相关文献

 作者相关
 关键词相关
 参考文献相关

版权所有 ©2008 中国科学院文献情报中心 制作维护:中国科学院文献情报中心
地址:北京中关村北四环西路33号 邮政编码:100190 联系电话:(010)82627496 E-mail:cscd@mail.las.ac.cn 京ICP备05002861号-4 | 京公网安备11010802043238号