锆基纳米复合储氢材料HTQAB2.1/Mg的微结构与电化学性能
The Microstructure and Electrochemical Performance of HTQAB_(2.1)/Mg Zr-Based Nanocomposity Hydrogen Storage Materials
查看参考文献14篇
文摘
|
采用球磨复合+烧结处理(BMS)及机械复合+烧结处理(MMS)两种方法制备了Zr0.9Ti0.1(Ni0.57V0.10Mn0.28Co0.05)2.1-XMg(X=10,20)锆基纳米复合储氢材料,经XRD、TEM-SAED分析表明,BMS和MMS的复合储氢材料皆由MgCu2型立方结构的单一C15-Laves相Zr基合金和密排六方结构的Mg金属构成,未发现两者之间的合金化效应,电化学测试表明,在60mA/g电流密度下,复合材料(MMS、BMS)活化性能好,MMS电极的最大放电容量为410mAh/g(X=20),而BMS的放电容量为360mAh/g(X=20)。在大电流密度下(≥3000mA/g),BMS电极的容量明显高于MMS电极,以BMS(HTQAB2.1-10Mg)电极的大电流放电性能为最好。因此,HTQB2.1锆基纳米复合材料不仅适用于高能量型NiMH动力电池而且更适用于高功率型NiMH动力电池。 |
其他语种文摘
|
The Zr-based nanocomposite hydrogen storage materials Zr_(0.9)Ti_(0.1) (Ni_(0.05)V_(0.12)Mn_(0.28)Co_(0.05))_(2.1)-x% Mg(X=10,20) were prepared by two ways: ball-milling + sintering treatment (BMS) and mechanical alloying + sintering treatment (MMS). XRD and TEM-SAED examinations show that microstructure of the materials is composed of MgCu_5-type cubic structure C15-Laves phase and hexagonal structure Mg. Their electrochemical performance tests show that the composite electrodes (MMS,BMS) have good activation properties at 60 mA/g current density. The maximum discharge capacity of MMS electrodes is 410 mAh/g(x=20), while BMS electrodes is 366 mAh/g(x=20). At high current density(≥3 000 mA/g), the discharge capacity of BMS electrodes is obviously higher than those of the MMS eletrodes. The BMS(HTQAB_(2.1)-10% Mg) electrode shows the best current density discharge performance.Therefore,HTQAB_(2.1) type Zr-based nanocomposite materials are suitable for not only high-energy NiMH batteries but also high-power NiMH batteries. |
来源
|
东北大学学报. 自然科学版
,2003,24(1):79-82 【核心库】
|
关键词
|
储氢材料
;
锆基纳米复合材料
;
HTQAB2.1/Mg
;
球磨复合
;
烧结处理
;
微结构
;
电化学性能
;
电动汽车
;
动力电池
;
蓄电池
|
地址
|
1.
东北大学理学院, 辽宁, 沈阳, 110004
2.
中国科学院金属研究所, 辽宁, 沈阳, 110016
|
语种
|
中文 |
文献类型
|
研究性论文 |
ISSN
|
1005-3026 |
学科
|
一般工业技术 |
基金
|
国家863计划
;
国家973计划
|
文献收藏号
|
CSCD:1298875
|
参考文献 共
14
共1页
|
1.
Corrigan D.
The 17~th International Electric Vehicle Symposium,2000:155-161
|
被引
1
次
|
|
|
|
2.
Kimura T.
The 15~th International Electric Vehicle Symposium,1998:363-372
|
被引
1
次
|
|
|
|
3.
Koehler U.
Nickel metal hydride batteries for automotive applications,1998
|
被引
1
次
|
|
|
|
4.
Yano Y.
The 17~th International Electric Vehicle Symposium,2000:322-327
|
被引
1
次
|
|
|
|
5.
Ovshinsky S R.
Science APRIL,1993,260(9):176-181
|
被引
66
次
|
|
|
|
6.
Chen L.
J Alloys Compd,1999,293/295:508-520
|
被引
14
次
|
|
|
|
7.
Dhar S K.
J Power Sources,1997,65:1-7
|
被引
15
次
|
|
|
|
8.
Kim D M.
J Alloys Compd,1999,293/295:583-592
|
被引
21
次
|
|
|
|
9.
Cracco D.
J Alloys Compd,1998,268:248-255
|
被引
2
次
|
|
|
|
10.
Bobet J L.
J Alloys Compd,2000,298:279-285
|
被引
3
次
|
|
|
|
11.
Yu J S.
J Alloys Compd,1998,278:283-288
|
被引
14
次
|
|
|
|
12.
Kim D M.
J Alloys Compd,1998,268:241-247
|
被引
6
次
|
|
|
|
13.
Andreas Z.
J Alloys Compd,1998,266:321-326
|
被引
1
次
|
|
|
|
14.
Wen M F.
J Mater Sci Technol,2001,17(1):S31-S34
|
被引
1
次
|
|
|
|
|