高强TB9钛合金次生α 相析出行为及力学性能
Precipitation behavior of secondary α phase and mechanical properties of high strength TB9 titanium alloy
查看参考文献18篇
|
文摘
|
研究单/双重时效热处理对TB9合金次生α相形貌及力学性能的影响规律。借助XRD分析合金相组成,采用光学显微镜和扫描电子显微镜观察显微组织,着重分析微观组织形貌随时效温度变化的演变特征,测试室温拉伸性能和断裂韧度。研究结果表明:单重时效时,晶粒内次生α相呈锯齿状和片层状析出,随着时效温度升高,α相尺寸增大,片层状α相含量增加;430 ℃时效时,合金强度较低,塑性较好,在470 ℃时效时合金强度最高;随时效温度的提高,强度先增大后维持在同一强度水平。双重时效时,晶粒内次生α相主要呈锯齿状析出,随时效温度升高,α相尺寸增大,抗拉强度先升高后降低,最高可达1542 MPa,且塑性变化较小。双重时效下合金的抗拉强度较单重时效大幅提高,这主要是由于晶界附近第二相析出强化和晶内锯齿结构α相的共同作用。 |
|
其他语种文摘
|
The precipitation behavior of secondary α phase and mechanical properties of high strength TB9 titanium alloy were investigated during single aging and duplex aging. The alloy phase constitution was analyzed by XRD,and the microstructure was observed by optical microscopy and scanning electron microscopy. The evolution characteristics of the microstructure with aging temperature were mainly analyzed. The room temperature tensile properties and fracture toughness were tested. The research results indicate that during single aging,secondary α phase exhibits serrated and layered precipitation. With increasing aging temperature, the size of α phase increases,and the content of layered α phase increases. The strength at 430 ℃ aging is lower and the plasticity is higher. The strength at 470 ℃ aging is the highest. With increasing aging temperature,the strength first increases and then maintains at the similar level. During duplex aging, most of secondary α phases precipitate in a serrated shape within the grains. With increasing aging temperature, the size of α phase increases, the tensile strength first increases and then decreases, reaching a maximum of 1542 MPa. The tensile strength of duplex aging is significantly higher than that of single aging,which is mainly due to the combined strengthening effect of second phases near grain boundaries and intragranular α phases with serrated shape. |
|
来源
|
航空材料学报
,2024,44(2):159-168 【核心库】
|
|
DOI
|
10.11868/j.issn.1005-5053.2023.000175
|
|
关键词
|
TB9合金
;
次生α 相
;
显微组织
;
力学性能
|
|
地址
|
中国科学院金属研究所, 师昌绪先进材料创新中心, 沈阳, 110016
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1005-5053 |
|
学科
|
金属学与金属工艺 |
|
基金
|
国家重点研发计划青年科学家项目
;
中国科学院青年创新促进会项目
|
|
文献收藏号
|
CSCD:7851413
|
参考文献 共
18
共1页
|
|
1.
李金山. 高强亚稳β 钛合金变形机制及其组织调控方法.
金属学报,2021,57(11):1438-1454
|
CSCD被引
6
次
|
|
|
|
|
2.
陈玮. 高强β钛合金的研究现状与发展趋势.
航空材料学报,2020,40(3):63-76
|
CSCD被引
13
次
|
|
|
|
|
3.
Ghosh A. Microstructure-fracture toughness correlation in an aircraft structural component alloy Ti-5Al-5V-5Mo-3Cr.
Materials Science and Engineering: A,2013,568:61-67
|
CSCD被引
9
次
|
|
|
|
|
4.
Boyer R R. Design properties of a high-strength titanium-alloy Ti-10V-2Fe-3Al.
Journal of Metals,1980,32(3):61-65
|
CSCD被引
1
次
|
|
|
|
|
5.
Rhodes C G. Influence of microstructure on mechanical-properties in Ti-3Al-8V-6Cr-4Mo-4Zr (Beta-c).
Metallurgical Transactions A,1977,8(11):1749-1761
|
CSCD被引
1
次
|
|
|
|
|
6.
Zhao Q Y. High-strength titanium alloys for aerospace engineering applications: a review on melting-forging process.
Materials Science and Engineering:A,2022,845:143260
|
CSCD被引
38
次
|
|
|
|
|
7.
Barriobero-Vila P. Phase transformation kinetics during continuous heating of a β-quenched Ti-10V-2Fe-3Al alloy.
Journal of Materials Science,2015,50(3):1412-1426
|
CSCD被引
1
次
|
|
|
|
|
8.
Grosdidier T. Effect of microstructure variations on the formation of deformation-induced martensite and associated tensile properties in a β metastable Ti alloy.
Metallurgical and Materials Transactions A,2000,31(4):1095-1106
|
CSCD被引
19
次
|
|
|
|
|
9.
Li T. The mechanism of ω-assisted α phase formation in near β-Ti alloys.
Scripta Materialia,2015,104:75-78
|
CSCD被引
1
次
|
|
|
|
|
10.
Zheng Y F. The role of the ω phase on the non-classical precipitation of the α phase in metastable β-titanium alloys.
Scripta Materialia,2016,111:81-84
|
CSCD被引
1
次
|
|
|
|
|
11.
Mantri S A. Tuning the scale of α precipitates in β-titanium alloys for achieving high strength.
Scripta Materialia,2018,154:139-144
|
CSCD被引
1
次
|
|
|
|
|
12.
Eylon D. Issues in the development of beta titanium alloys.
Journal of the Minerals,Metals & Materials Society,1994,46(7):14-15
|
CSCD被引
1
次
|
|
|
|
|
13.
尚庆慧. 固溶和时效处理对TB9钛合金显微组织及力学性能的影响.
热加工工艺,2023,52(14):147-149
|
CSCD被引
1
次
|
|
|
|
|
14.
Xu X. Hot deformation behavior and microstructural evolution of beta C titanium alloy in beta phase field.
Transactions of Nonferrous Metals Society of China,2016,26(11):2874-2882
|
CSCD被引
1
次
|
|
|
|
|
15.
郭金明. 热处理工艺对TB9钛合金棒材组织和性能的影响.
湖南有色金属,2023,39(2):44-46
|
CSCD被引
1
次
|
|
|
|
|
16.
高文静. 变形量和时效对TB9钛合金丝材组织和性能影响.
世界有色金属,2020(12):154-155
|
CSCD被引
3
次
|
|
|
|
|
17.
Lan C. Influence of oxygen content on the microstructure and mechanical properties of cold rolled Ti-32.5Nb-6.8Zr-2.7Sn-xO alloys after aging treatment.
Journal of Materials Science & Technology,2018,34:2100-2106
|
CSCD被引
1
次
|
|
|
|
|
18.
Shanoob B. On variant distribution and coarsening behavior of the α phase in a metastable β titanium alloy.
Acta Material,2016,106:374-387
|
CSCD被引
1
次
|
|
|
|
|
了解气象卫星更多信息，请访问