铝基体上等离子体电解氧化陶瓷涂层的冲蚀性能
Erosion performance of plasma electrolytic oxidation ceramic coating on aluminum substrate
查看参考文献9篇
|
文摘
|
采用气流喷砂式冲蚀试验机,对铝合金基体的等离子体电解氧化(PEO)陶瓷层进行冲蚀性能研究。利用扫描电子显微镜及精密天平,检测了PEO陶瓷层的表面冲蚀形貌及冲蚀磨损量,比较分析了粒子速度、入射角度对冲蚀磨损率及冲蚀形貌的影响规律。结果表明,PEO陶瓷涂层在受冲蚀时表面裂纹萌生扩展导致材料破碎成细块脱落,属于典型的脆性材料冲蚀行为;PEO陶瓷涂层冲蚀磨损率随入射角度的减小逐渐降低,对低角冲蚀表现良好的抗冲蚀能力;粒子速度对PEO陶瓷层冲蚀磨损率的影响非常明显,其速度指数为2.7。 |
|
其他语种文摘
|
Using air-blast erosion test machine,the erosion performance of plasma electrolytic oxidation ( PEO) ceramic coatings on aluminum alloy substract was studied. Surface morphology and erosion mass loss of PEO ceramic coatings were tested by scanning electron microscopy and precision scales,and the effects of particle velocity and incident angle on erosion rate and erosion morphology were analyzed. The results show that cracks initiation and propagation on the surface of PEO ceramic coatings after erosion which makes the material break into thin pieces and fall off. Therefore,the erosion of PEO ceramic coatings is a typical brittle material erosion behavior. But the erosion rate of PEO ceramic coatings gradually reduces with the reduction of incident angle,and the PEO ceramic coatings show good erosion resistance when the incident angle is low. Meanwhile,the particle velocity on the erosion rate of PEO ceramic coating has an obvious effect,and the speed index is 2.7. |
|
来源
|
金属热处理
,2015,40(9):84-87 【核心库】
|
|
DOI
|
10.13251/j.issn.0254-6051.2015.09.016
|
|
关键词
|
等离子体电解氧化
;
陶瓷涂层
;
冲蚀
;
入射角度
;
粒子速度
|
|
地址
|
1.
南车青岛四方机车车辆股份有限公司, 山东, 青岛, 266000
2.
中国科学院力学研究所, 北京, 100190
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
0254-6051 |
|
学科
|
金属学与金属工艺 |
|
文献收藏号
|
CSCD:5527926
|
参考文献 共
9
共1页
|
|
1.
汤文博. 冲蚀条件下等离子喷涂Al_2O_3陶瓷涂层的磨损特性.
郑州大学学报(工学版),2002,23(1):39-41
|
被引
1
次
|
|
|
|
|
2.
高雪松. 等离子喷涂纳米ZrO2复合陶瓷涂层冲蚀行为.
材料热处理学报,2010,31(10):136-140
|
被引
2
次
|
|
|
|
|
3.
廉晓庆. 不同冲蚀角下非均质脆性材料的残余应力和冲蚀机制.
硅酸盐学报,2011,39(11):1740-1746
|
被引
1
次
|
|
|
|
|
4.
Oka Y I. Impact-angle dependence and estimation of erosion damage to ceramic materials caused by solid particle impact.
Wear,2009,267(1):129-135
|
被引
16
次
|
|
|
|
|
5.
Bousser E. Solid particle erosion mechanisms of hard protective coatings.
Surface and Coatings Technology,2013,235(25):383-393
|
被引
5
次
|
|
|
|
|
6.
Aminul Islam Md. Effect of impact angle and velocity on erosion of API X42 pipeline steel under high abrasive feed rate.
Wear,2014,311(1/2):180-190
|
被引
12
次
|
|
|
|
|
7.
Hutchings I M. The erosion of ductile metals by spherical particles.
Journal of Physics D: Applied Physics,1975,8(1):8-14
|
被引
1
次
|
|
|
|
|
8.
Lidija Curkovic. Solid particle erosion behaviour of high purity alumina ceramics.
Ceramics International,2011,37(1):29-35
|
被引
4
次
|
|
|
|
|
9.
Wang Xiaojun. Solid particle erosion of alumina ceramics at elevated temperature.
Materials Chemistry and Physics,2013,139:765-769
|
被引
2
次
|
|
|
|
|
了解气象卫星更多信息，请访问