激光毛化形貌对轮轨材料混合润滑摩擦系数的影响
Effect of Laser Textured Patterns on Friction Coefficient of Wheel/ Rail Materials under Mixed Lubrication
查看参考文献25篇
|
文摘
|
为了研究规则分布的表面形貌对轮轨接触在混合润滑状态下摩擦系数的影响,设计了3种不同的表面纹理:横纹、纵纹、菱形。用确定性模型取代平均流量模型,对膜厚、压力、接触面积比进行了数值计算,总的接触载荷由流体接触区和固体接触区分别分担,总的摩擦力等于流体区的摩擦力和固体接触区摩擦力之和。根据设计的3种表面纹理,用YAG激光对车轮钢试样表面进行激光毛化处理,获得这3种表面纹理,在RSW-2摩擦磨损试验机上进行油介质条件下的混合润滑摩擦学实验,模拟轮轨间有油污时的工况,测量了该条件下各种表面纹理下的摩擦系数,并与未作激光毛化处理的表面进行对比。理论和实验结果显示,在油介质混合润滑条件下,有激光表面纹理的摩擦系数远大于未作激光毛化处理的试样表面的摩擦系数。3种激光表面纹理中,菱形纹理的摩擦系数大于纵纹和横纹的摩擦系数,纵纹的摩擦系数比横纹略大。因此,在油污条件下使用激光毛化的菱形纹理表面能较显著地提高轮轨间的摩擦系数。 |
|
其他语种文摘
|
To investigate the influences of regular patterns on friction coefficients of wheel-rail contact under mixed lubrication, longitudinal, transverse and rhombus patterns are designed. The film thickness, pressure and contact area ratio are calculated by using deterministic model instead of average flow model. Based on the load-sharing concept, the hydrodynamic film and asperities both contribute to carrying the total load. Therefore the friction force is composed of hydrodynamic friction force and asperity friction force. According to the designed patterns, the surfaces of wheel discs are textured by YAG laser. The friction coefficients are tested on a RSW-2 type wear testing machine and the results are compared with that of the grinded without laser textured. It is shown theoretically and experimentally that the friction coefficient of rhombus pattern is higher than that of longitudinal and transverse patterns. And the friction coefficient of longitudinal pattern is slightly higher than that of transverse pattern. Therefore, laser texturing of the textured surface with rhombus distribution can increase the friction coefficient obviously between wheel and rail under oil-contamination condition. |
|
来源
|
中国激光
,2015,42(6):0603003-01-0603003-08 【核心库】
|
|
DOI
|
10.3788/CJL201542.0603003
|
|
关键词
|
激光技术
;
摩擦系数
;
激光毛化
;
混合润滑
|
|
地址
|
1.
中国科学院力学研究所, 中国科学院先进制造工艺力学重点实验室, 北京, 100190
2.
北京理工大学机械与车辆工程学院, 北京, 100190
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
0258-7025 |
|
学科
|
物理学 |
|
基金
|
国家自然科学基金
;
国家973计划
|
|
文献收藏号
|
CSCD:5457135
|
参考文献 共
25
共2页
|
|
1.
Ohyama T. Traction and slip at higher rolling speeds: Some experiments under dry friction and water lubrication.
The 1st International Conference on Contact Mechanics and Wear of Rail/Wheel Systems,1983:395-418
|
CSCD被引
1
次
|
|
|
|
|
2.
Ohyama T. Tribological studies on adhesion phenomena between wheel and rail at high speeds.
Wear,1991,144(1/2):263-275
|
CSCD被引
18
次
|
|
|
|
|
3.
Zhang W H. Wheel/rail adhesion and analysis by using full scale roller rig.
Wear,2002,253(1/2):82-88
|
CSCD被引
13
次
|
|
|
|
|
4.
Chen H. Adhesion between rail/wheel under water lubricated contact.
Wear,2002,253(1/2):75-81
|
CSCD被引
25
次
|
|
|
|
|
5.
Patir N. An average flow model for determining effects of three- dimensional roughness on partial hydrodynamic lubrication.
J Lubri Technol Trans ASME,1978,100(1):12-17
|
CSCD被引
227
次
|
|
|
|
|
6.
Chen H. Analysis of adhesion under wet conditions for three- dimensional contact considering surface roughness.
Wear,2005,258(7/8):1209-1216
|
CSCD被引
26
次
|
|
|
|
|
7.
Krupka I. Effect of surface texturing on mixed lubricated non- conformal contacts.
Tribology International,2008,41(11):1063-1073
|
CSCD被引
7
次
|
|
|
|
|
8.
Nanbu T. Increase of traction coefficient due to surface micro texture.
Tribol Lett,2008,29(2):105-118
|
CSCD被引
5
次
|
|
|
|
|
9.
Akbarzadeh S. On the prediction of running-in behavior in mixed-lubrication line contact.
J Tribol Trans ASME,2010,132(3):032102
|
CSCD被引
5
次
|
|
|
|
|
10.
Akbarzadeh S. Experimental and theoretical investigation of running-in.
Tribology International,2011,44(2):92-100
|
CSCD被引
4
次
|
|
|
|
|
11.
Chen H. Experimental investigation of influential factors on adhesion between wheel and rail under wet conditions.
Wear,2008,265(9/10):1504-1511
|
CSCD被引
25
次
|
|
|
|
|
12.
Hu Y Z. A full numerical solution to the mixed lubrication in point contacts.
J Lubri Technol Trans ASME,1999,122(1):1-9
|
CSCD被引
1
次
|
|
|
|
|
13.
Zhu X D. Effects of rough surface topography and orientation on the characteristics of EHD and mixed lubrication in both circular and elliptical contacts.
Tribol Trans,2001,44(3):391-398
|
CSCD被引
1
次
|
|
|
|
|
14.
Zhu D. Effect of surface roughness on mixed EHD lubrication characteristics.
Tribol Trans,2003,46(1):44-48
|
CSCD被引
5
次
|
|
|
|
|
15.
林子光. 激光毛化与摩擦学设计.
机械设计,2000,17(4):24-27
|
CSCD被引
7
次
|
|
|
|
|
16.
占剑. 脉冲YAG激光波形对缸套内壁激光刻蚀微坑形貌的影响.
中国激光,2011,38(6):0603032
|
CSCD被引
2
次
|
|
|
|
|
17.
邢旭辉. CL60车轮材料表面激光离散熔凝的滚动磨损形貌.
中国激光,2013,40(3):0303006
|
CSCD被引
2
次
|
|
|
|
|
18.
王保安. 激光离散熔凝对小滑差率接触疲劳性能的影响.
应用激光,2014,34(6):518-523
|
CSCD被引
1
次
|
|
|
|
|
19.
郭士锐. 大功率半导体激光表面改性的研究进展.
激光与光电子学进展,2013,50(5):050004
|
CSCD被引
4
次
|
|
|
|
|
20.
Izhak Etsion. State of the art in laser surface texturing.
J Tribol Trans ASME,127(1):248-253
|
CSCD被引
1
次
|
|
|
|
|
了解气象卫星更多信息，请访问