碳纳米管/炭黑/硅橡胶复合材料的压阻计算模型分析
Analysis of pressure-resistance calculating model of carbon nanotubes/carbon black/silicone rubber composite material
查看参考文献10篇
|
文摘
|
以碳纳米管、炭黑为填料,硅橡胶为基体制备柔性压力敏感材料。将炭黑填充硅橡胶的压阻计算模型扩展应用于碳纳米管/炭黑/硅橡胶材料,研究了不同填料配比下的碳纳米管/炭黑/硅橡胶的渗流特性,并通过实验对计算模型进行了分析。结果表明,在碳纳米管/炭黑/硅橡胶体系中,选择适合的碳纳米管和炭黑组分配比,可获得较低的渗流阈值,且压阻实验结果与计算曲线偏差较小;由于碳纳米管和炭黑的协同效应和通用有效介质理论适用的边界条件,使得在碳纳米管/炭黑以一定的配比混合下,并用的导电填料体积分数略偏离阈值附近时,实验结果与计算模型曲线可以较好地吻合。 |
|
其他语种文摘
|
In the paper, flexible pressure sensitive composite materials of silicone rubber filled with carbon nanotubes (CNTs) and carbon black(CB) were prepared. The carbon black filled silicone rubber pressure-resistance calculating model is extended to carbon nanotubes/carbon black/silicone rubber composite materials. The percolation characteristics of carbon nanotubes/carbon black /silicone rubber with different mixing ratio were studied and calculating model was analyzed by the experiment. The results show that in carbon nanotubes/carbon black/silicon rubber system, the lower percolation threshold can be obtained by selecting the appropriate carbon nanotubes and carbon black mixing ratio, the smaller deviation of the experimental results and the calculating curve is got. For the synergistic effects of carbon nanotubes and carbon black in a rubber system and general effective media theory applicable boundary conditions, when CNTs/CB was in a certain mixing ratio, and volume fraction of slightly deviate from near percolation threshold, the experimental results are better consistent with the calculating model curve. |
|
来源
|
功能材料
,2013,44(5):669-672 【核心库】
|
|
关键词
|
碳纳米管
;
炭黑
;
导电复合材料
;
压阻计算模型
;
协同效应
|
|
地址
|
1.
合肥工业大学电子科学与应用物理学院, 安徽, 合肥, 230009
2.
中国科学院合肥智能机械研究所, 安徽, 合肥, 230031
|
|
语种
|
中文 |
|
文献类型
|
研究性论文 |
|
ISSN
|
1001-9731 |
|
学科
|
一般工业技术 |
|
基金
|
国家自然科学基金资助项目
;
国家863计划
|
|
文献收藏号
|
CSCD:4799057
|
参考文献 共
10
共1页
|
|
1.
Lu Junyong. Study of piezoresistance effect of carbon nanotube-PDMS composite materials for nanosensors.
IEEE International Conference on Nanotechnology,2007:1240-1243
|
被引
1
次
|
|
|
|
|
2.
Yang Bo. Multiwall carbon nanotubes enhanced conductive behaviors of CB/PP electrical conductive composites.
Acta Mater Compos Sinica,2009,4(26):41-46
|
被引
1
次
|
|
|
|
|
3.
Dang Zhimin. Complementary percolation characteristics of carbon fillers based electrically percolative thermoplastic elastomer composites.
Composites Science and Technology,2011,72:28-35
|
被引
3
次
|
|
|
|
|
4.
Wang Peng. Piezoresistivity of conductive composites filled by carbon black particles.
Acta Mater Compos Sinica,2004,21(6):34-38
|
被引
3
次
|
|
|
|
|
5.
Liu Ping. Strain and piezoresistive effect in working principle of pressure-sensitive conductive rubber.
Polym Mater Sci Eng,2011,27(5):112-115
|
被引
3
次
|
|
|
|
|
6.
Mclachlan D S. Messurement and analysis of a model dual conductivity medium using a generalized effective medium theory.
J Phys C,1988,21(8):1521-1532
|
被引
4
次
|
|
|
|
|
7.
Liu Enlong. Conductive properties of polymer composites filled with two kinds of carbon materials and calculating model of its percolation threshold.
J Funct Polym,2011,24(3):248-255
|
被引
1
次
|
|
|
|
|
8.
Fan Zhuangjun. The synergetic effect of carbon nanotubes and carbon black in a rubber system.
New Carbon Mater,2008,23(2):149-153
|
被引
3
次
|
|
|
|
|
9.
Hang Ying. The influence of filled carbon black on the properties of conductive silicon rubber used in flexible tactile sensor.
Journal of Functional Materials,2010,41(2):225-231
|
被引
2
次
|
|
|
|
|
10.
Wang Zhifeng. Processing and modeling of multi-walled carbon nanotube/styrene-butadiene-styrene (SBS) composites.
IEEE Conference on Nanotechnology,2009:756-757
|
被引
1
次
|
|
|
|
|
了解气象卫星更多信息，请访问